#481W7 –96’/ 260,000# HOPPER TELESCOPING DERRICK – KEPT IN FINE SHAPE

Hopper GXXTA 1977 4 Axle Carrier

12V71TT Detroit Diesel Engine

5860 Allison Transmission

Hydraulic Winch

Power Swivel Hydraulic System and Control on Rig

BJ Model RS Tubing Tongs w/ Air Backup And Heads

Cavins Modal B Airslips, BJ Rod Hook

McKissick Figure 83A – 3 Sheave Weighted Blocks

2 3/8” and 2 7/8” 100 Ton Double Latch Elevators

150,000# Shur Weight Pad Type Indicator

5/8, 3/4, 7/8, and 1” Elevators and Wrenches

1 3/4” x 84” Bails, Sala Fall Protection

Climb Assist, Base Beam

Misc. Hand Tools ie. Pipe Wrenches, Hammer Wenches,  etc.

This is a 1 Owner rig That Has Been Kept in EXCELENT SHAPE.
You Must See This Rig - to Appreciate The Rig Condition

Arrangements Can be made For SERIOUS BUYERS to Inspect Rig in Texas. (800) 304-9014 or (512) 291- 6434

#476W7 – 1981 MODEL LTO 350 COOPER – WORKOVER – WELL SER.

Double-Drum “Back-In” Double-Triple Well Service Unit

With 96’ Pemco Derrick (S/N 1042)

Witchita Air Clutches, Powered By Detroit 8-V Diesel Engine

With 6-Speed Allison Transmission, Right Angle Drive

Mounted on 4 Axle Carrier

11.00 x 20 Rear Tires, 16.5 x 22.5 Front Tires

Hydraulic System and Air System

Hydraulically Raised and Scoped, Complete with Rod and

Tubing Board and Working Platform

Arrangements Can be made For SERIOUS BUYERS to Inspect this Rig in Texas. Contact us to Make Arrangement.

#475W7 - HYDRAULIC WORKOVER RIG M-2500, MOUNTED ON 1988 INTERNATIONAL TRUCK WITH V-8 INT’L DIESEL ENGINE.  DOUBLE DRUM – POWERED BY A 453 DETROIT DIESEL ENGINE WITH AIR THROTTLE.  CAN PULL DOUBLE ROD AND SINGLE TUBLING.  HYDRAULIC OIL COOLER AND 3 HYDRAULIC LEVELING JACKS.

Model 74 Foster Power Tongs – with Hydraulic lift
Air Slips and Controls
2-3/8 Elevators
2-7/8 Elevators
Oil Saver with Pump, Line and Pump
Sinker Bar
Elevator Bells
Stiff Arm For Power
Extra New Tubing Lines
New Battery on 453 Detroit Engine
50 Gallon Diesel Tank
Foot and Hand Throttle

This Unit has been Repainted in last Year

Contact us With Questions….1- 800-304-9041

This Rig is Ready to work.  Arrangements Can be made
For SERIOUS BUYERS to Inspect this Rig in Central Texas.

#474W7 – FRANKS  DOUBLE – SINGLE WORKOVER-WELL SERV. RIG

Franks 658-65-DTM Drawworks Blue Well Service Unit with 7/8” x 500’ Tubing Line, 9/16 x 4,500’ Sandline, Powered by Detroit 8V-71 Diesel Engine with Allison 750 Transmission, 69’ x 150,000#
4-Leg Franks Telescoping Servicer Tubular Mast with singular
Raising Ram, On 1981 SKYTOP 4-Axle Carrier with 4-Hydraulic
Leveling Jacks with Jack Stands.  Utility Winch, 2 Fuel Tanks,
4 Tool Boxes, Parts Cage, Air and Hydraulic Tanks, Work Platform,
15.00 x 22.5 Front Tires.  Brake Drum Cooling Water system,
Totco Weight Indicator and Pads, Derrick Climber.

Refurbishment History:

Engine Rebuilt:  2007

Transmission Rebuilt:  2007

Derrick Top Section Replaced:  2008

New Tulsa Hydraulic Utility Winch:  2008

Rear-Drive Axles Rebuilt:  2007

Front Hendrickson Walking Beam Suspension Rebuilt: 2007

Tubing Drum Brake Bands Linkage Pads Replaced: 2007

New Bendix Air Compressor:  2008

New Swedge-Type 7/8” Tubing (drilling) Line: 2008

Three-Shieve Traveling Blocks Rebuilt: 2008

Foster 58 Tongs Rebuilt:  2008

Air-over-Grease Sand Drum Actuator Rebuilt:  2010

Tools:

Two 6’  Tubing Bells
Two 3/8”  Upset Tubing Double-Latch Elevators
2 7/8” Upset Tubing Double-Latch Elevators
Cavins Tubing Slips
Ratigan Rod Hook
Two ¾” x 7/8” Rod Elevators
Two ¾” x 5/8” Rod Elevators
Two ¾” x 7/8” Rod Wrenches
Two 5/8” x Rod Wrenches
Guiberson Double-Pack Oil Saver
One 2” Slip-Type baby Red Rod Fishing Tool
One 2-3/8” Mouse Trap Rod Fishing Tool
One 2-7/8” Mouse Trap Rod Fishing Tool
Miscellaneous Hand Tools
 
Contact us With Questions….1- 800-304-9041

This Rig is Ready to work.  Arrangements Can be made ForSERIOUS BUYERS to Inspect this Rig in Central Texas.

#473W7 – FRANKS  DOUBLE – TRIPLE WORKOVER-WELL SERV. RIG

Franks 65-658- DTD Drawworks with Twin-Disk Clutch with Oil-Cooled Air Seal, Double-Drum Red Well Service Unit with 7/8” x 615’ of Tubing Line, 9/16” x12,000’ of New Sand Line, Powered by Detroit
8V-71 Diesel Engine with Allison 750 Transmission, 96’- 180,000#
Pemco Y- Base Telescoping Mast with Single Raising Ram, on
1978 Crane 4-Axle Carrier with 4 Hydraulic leveling Jacks with
Jack Stands.  Utility Winch, 2 Fuel Tanks, 3 Tool Boxes, Parts
Cage, Air and Hydraulic Tanks, Work Platform, 15.00 x 22.5 Front
Tires, 11R22.5 Rear Tires.  Brake Drum Cooling Water System,
Totco Weight Indicator and Pads, Derrick Climber.

Refurbishment History:

Engine Rebuilt: Late 2008

New Tubing Drum Brake Flanges, Linkage, Sprokets,
            Chains, Brake Bands and Pads: Late 2008

Rebuilt Right-Angle Drive Box: 2008

New Steering Box: 2006

Drive Axle Rebuilt: 2007

New Work Floor: 2007

Up-Graded Hydraulic System: 2007

Sand Blasted and Painted: 2007

Tools:
           Two 6’ Tubing Bells
           Two 3/8” Upset Tubing Double Latch Elevators
           2 7/8” Upset Tubing Double Latch Elevators
           Foster 58 Tubing Tongs
           Cavins Tubing Slips
           Ratigan Rod Hook
           Two ¾” x 7/8” Rod Elevators
           Two ¾” x 5/8” Rod Elevators
           Two ¾” x 7/8” Rod Wrenches
           Two 5/8” Rod Wrenches
           Guiberson Double- Oil Saver
           One 2” Slip-Type Baby Red Rod Fishing Tool
           One 2 3/8” Mouse-Trap Rod Fishing Tool
           One 2 7/8” Mouse-Trap Rod Fishing Tool
           Miscellaneous Hand Tools
 
Contact us With Questions….1- 800-304-9041

This Rig is Ready to work.  Arrangements Can be made ForSERIOUS BUYERS to Inspect this Rig in Central Texas.

#472W7 – Franks 658 – WORKOVER – WELL SER. RIG  

96’ Four Legged Derrick

8V92 Detroit Engine

4460 Allison Transmission

100 Ton Ideco Block

Parmac Hydromatic

Newly Rebuilt Engine

Gone Through Drawworks

Arrangements Can be made For SERIOUS
BUYERS to Inspect this Rig in Texas.
Contact us to Make Arrangement

#470W6– BRAND NEW 2009 WORKOVER / WELL SERVICE / DRILLING RIG

RIG SPECIFICATIONS:

1. Six (6) Axle Back-In Carrier
2. Two (2) Detroit Diesel Series 60 – 450 HP Engines, Equipped with High Ambient Temperature Radiators, Alternators, Starters, Air
   Compressors, Power Steering Pump, Emergency Shut Downs, All
   Gauges and Filters, 12 Volt Electrical System
3. Two (2) Allison 5860, Six (6) Speed Automatic Transmission with Torque Convertors and Filtration System
4. Full Fabricated Chassis Rails with Bumpers and Tow Hooks
5. Three (3) 20,000# Steering Axles with Hendrickson Suspension and DOT Air brakes
6. Three (3) 23,000# Rear Driving Axles with Hendrickson Suspension and Interaxle Locks.  Emergency and Parking Brake System
7. Single Man Cab with Adjustable Seat Belt and Instrumentation
8. Rig Decked with 3/16” Textured Decking, Equipped with Four (4) Hydraulic Leveling Jacks, Walk-ways are Static Free Fibergrate,
   Tool Boxes and Junk Boxes to Customer Preference
9. Two (2) 12,000# Hydraulic Winches  

750 HORSEPOWER HOPPER  FWA DRAWORKS:

1. Main Drum.
         46” x 12” Brake Flanges
         Brake Area 3120 Sq. In.
         Barrel Diameter  22-3/8”
         Barrel Length  42”
         Drum Capacity  1-1/8 Line  3,620’
         Drum Clutch  32 VC-1000 Fawick Outboard
         Input Chain 1-1/4 Quad
         Drum To Drum Chain  1-3/4”
         Hydromatic Chain  1-1/4” Quad
         Assist Brake  V-80 Parmac
         Drawworks Speed - Five (5) Forward – One (1) Reverse
2. Sand Drum
          42” x 10”  Brake Flanges
          Brake Area 2400 Sq. In.
          Barrel Dia.  14-5/8”
          Barrel Length  41-5/16”
          Drum Capacity with 9/16” Line – 15,540’
          Drum Clutch 30” Hopper
3. Two (2) Hopper Right Angle Drives
4. All Chains – Oil Immersion
5. Secondary Cooling System for Hydromatic – Consisting of   Hydraulically Operated Charge Pump and Air to Fluid high
   Heat transfer Assembly
6. Two Position Operators Console Primary at Deck Level and Secondary At Substructure Level.  Console Includes Clutch,
   Throttle, Rotary Drive, Transmission Shifters, Start, Kill, Hydraulic
   Pump, Air Slips, Hydraulic Pressure Regulator, Emergency
   Engine Warning Lights, Brake Water, And Winch Controls
7. 53 Gallon Hydraulic System Complete with Pump, Tank, Filters, Erection Controls, and Tong Circuit
8. Drum Type Dead Line Anchor mounted Directly to Frame
9. Drill Line Spool
10. Work Floor with Handrails and Static Free Fibergrate Flooring
11. Rotary Drive with Elevated Chain Case to Match Substructure

DERRICK

1. 112’ x 400,000# Capacity Hopper Telescoping Mast
2. Two (2) Single Acting Hydraulic Scoping Ramps
3. Two (2) Single Acting Three Stage Raising Cylinders
4. Racking Board 2 Position 54’ and 66’ Auto Deployment and Retraction
5. 4” x 5000 PSI Stand Pipe with Gooseneck
6. Ten (10) Line Crown
   1 -  1-1/8” x 30” Deadline Sheave
   4 -  1-1/8” x 30” Cross Mounted Reaving Sheavs
   1 -  1-1/8  x 30” Fast Line Sheave
   1 -  9/16”  x 24” Sand Line Sheave
7. Wind Guys and Load Guys Installed
8. Geronimo Escape Post
9. Fall Protection ………………………………………….. Price Each

SUBSTRUCTURE

1. Twelve (12) Foot Substructure
2. 17-1/2” Mechanical Rotary Table
3. Catwalk and V-Door Part of Wheel Mounted Assembly
4. 400,000# Setback Capacity
5. All Handrails and Stairways …………………….……. Price Each

TRIPLEX PUMPS – 600 HP

1. 600 Rated Brake HP 
2. 100,000# - Maximum Rod Load
3. 6” – Stroke Length
4. 2 – ¾” – 5” Plunger Diameter
5. 53- 7/16” Overall Length
6. 600 HP Series 60 Detroit Diesel
7. High Ambient Temperature Cooling System
8. Starter
9. Alternator
10. Allison 6061  6 Speed Automatic Transmission
11. PTO Driven Hydraulic System
12. 4” Charge Pump
13. 5” Valve High Pressure Manifold
14. 5000 PSI Mud Gauge
15. All Mounted on 3 Runner Oil Field Skid ………………… Price Each

POWER SWIVEL – MASTER SKID MOUNTED POWER SWIVEL UNIT

1. 2.5 Power Swivel
2. 85,000# Load Rated
3. Powered by 4.4 Liter Caterpillar Engine
4. Air Operated remote Controls
5. All Tanks, Electrical, and Operating Controls Included
6. Hydraulic Hoses From Power Unit to Swivel Unit Includ…Price Each
     

This Rig will be Totally NEW, Built to the above Specifications.
Certain items could be altered based on Customer Requirements.

#466W4 – 2002 HOPPER WORKOVER RIG – 500 HP – VERY GOOD CONDITION

106’ – 300,000# Hopper TELESCOPING Derrick

GXHTA Hopper Drawworks

12” x 42” Main Drum

10” x 42” Sanddrum

Detroit Diesel Series 60 Engine

Allison S5600H – 6 Speed Automatic Transmission

Parmac 202 Hydromatic

Work Floor With Handrails

12,000# Hydraulic Winch

BJ Hydraulic Tubing Tongs

84” x 1-3/4” Links

2-3/8”  100 Ton Tubing Elevators

2-7/8”  100 Ton Tubing Elevators

Cavins Model C Air Slips

Contact us With Questions….1- 800-304-9041

This Rig is Ready to work. Arrangements Can be made For SERIOUS BUYERS to Inspect this Rig.

#462W4 – 1980 CORSAIR 400 Series – WORKOVER RIG  

96’ – 215,000# Capacity, Double-Triple

Double Drum “Back-In” 5 Axle Workover Rig

Crane Carrier, Single Man Cab

Braden A-8 Hyd., 2 Tool Boxes 4 Hyd. Leveling Jacks

Folding Walkways, Removable Safety Rails,

44,000# Front and Rear Axles

15 x 22.5 Front Tires, 10 x 20 Rear Tires

SSHD Front and Rear Ends

Mast – Model 96-215-C

3 Stage Raising Rams, 215,000# with 6 Lines to Block

Engine is 8V92N Detroit Diesel-Mod 8087-7000

435 HP Allison Automatic 211117B21 Drawworks

Model 400 Lebus Grooved Drum

Parmac 22Sr 22” Single Hydromatic Brake

100 Ton McKissick Traveling Blocks, and Sandline

Contact us With Questions…1-800-304-9041

This Rig is Ready to work. Arrangements Can be made For SERIOUS BUYERS to Inspect this Rig in Central Texas.

#460W4 – 1985 CRANE CARRIER –WORKOVER - WELL SERV. RIG  

96’ – 215,000# Capacity, C Corsair Mast

Double Drum “Back-In” Double-Triple Well Servicing Unit

Twin Disc Air Clutches Powered By Detroit 8V92T, 8 Cyl Eng.

Allison CLT-5861 Transmission

5 Axle Carrier, Tires- 11 x 20 Rear, 15 x 22.5 Front

Hydraulic System and Air System

Hydraulically Raised and Scoped

Complete with Rod and Tubing Board

Working Platform

Blocks and Sandline

This Unit has been Repainted in last Year

Contact us With Questions…1-800-304-9041

This Rig is Ready to work. Arrangements Can be made For SERIOUS BUYERS to Inspect this Rig in Central Texas.

#458W4 – 1981 CORSAIR CRANE CARRIER –WORKOVER - WELL SERV. RIG  

96’ – 210,000# Capacity, Recently Working

Hydraulically Raised and Scoped Mast,

3 Sheave Crown Block,

Crown Safety Platform,

Rod Basket, Racking Board, Ladder, Escape Device,

Guylines & Anchors, Mounted Integral with Corsair W3284A

Double Drum Lebus-Grooved Drawworks,

Parmac 15” Double Hydromatic brake, Driller’s Controls,

Hydraulic & Air Compressor Systems Powered by Detroit Diesel

8V71 Radiator Cooled Diesel Engine With Allison 5860

Torque Convertor, All Mounted on CCC 5-Axle, Back-in Carrier

With 4 Hydraulic Leveling Jacks, 5’ Step,

Derrick Rig Work Platform, 2’ x 16’ Extended walkway with

Handrails, 2-pin type anchors

Blocks & Sandline

Contact us With Questions…1-800-304-9041

This Rig is Ready to work. Arrangements Can be made For SERIOUS BUYERS to Inspect this Rig in Central Texas.

#442W4 – BRAND NEW 2009 CORSAIR 400 – WELL SERVICE / W.O. RIG

5 Axle Back-In Carrier

42” x 10” Mail Drum

42” x 8” Sand Drum

104” x 250,000# Derrick API 4-F Monogramed

Series 60 Detroit

5610 Allison Transmission

48” Kobelt Disc Assist Brake

All NEW Construction

Still Can Pick Colors
 
Ready in January 2009

Contact us With Questions…1-800-304-9041

Arrangements Can be made For SERIOUS
BUYERS to Inspect this Rig in West Texas.
Contact us to Make arrangement

#438W4 – 1983 FRANKS 1058 – WELL SERVICE / W.O. RIG,  

CARRIER MOUNTED - 96 ft – 180,000# Double-Triple
Allison Automatic Transmission
Powered by 8V71 Detroit
Pemco 4 Legged Derrick
Tubing Line & Block
NO Sand Line or Tools furnished

Contact us With Questions…1-800-304-9041

Arrangements Can be made For SERIOUS
BUYERS to Inspect this Rig in West Texas.
Contact us to Make arrangement

#880D7 – OIL WELL E-2000 COMPLETE WITH ALL COMPONENTS DESCRIBED:

THIS COMPLETE, EXCELLENT QUALITY, ELECTRIC RIG WITH ALL PARTS,
NEW AND SOME REFURBISHED, IS ON SEVERAL OF FOLLOWING PAGES.
GIVE US YOUR NAME, E-MAIL OR PHONE # WE CAN SEND INFORMATION,

TexacaliOil@aol.com

      INDEX:   SECTION 1000        DRAWWORKS AND ACCESSORIOS
                       SECTION 2000        MUD PUMPS AND ACCESSORIES
                       SECTION 3000        POWER AND SCR SYSTEM
                       SECTION 4000        MAST AND SUBSTRUCTURE
                       SECTION 5000        MUD SYSTEM AND ACCESSORIES
                       SECTION 6000        HOUSES/TANKS/MISCELLANEOUS EQUIP.
                       SECTION 7000        RIG-UP

SECTION 1000 - DRAWWORKS AND ACCESSORIES

ITEM 1001 - 1 Each OILWELL E-2000, 2000 HP Drawworks as Follows (Rebuilt):           Welded Structural Steel Frame and Housing, Drum with Grooving For
            For 1-3/8” Drill Line, Water Cooled Brake Flanges, Hydraulic Spinner
            And Breakout with Controls Mounted on Floor (New), 42” x 10” High
            Drum Clutch (New), 36-C Two Plate Low Drum Clutch (new), Motor
            Drive Chain (new), Drum Drive Chains (New), Catshaft Drive Chain (New),
            Induction Hardened Cut Tooth Sprockets, Pressure Spray Oil
            Lubrication to All Chains, Lubrication Pump, Self- Aligning Main Shaft
            Roller Bearings, Air Controlled Transmission Clutches, Air Controlled
            Catshaft Disconnect Clutch, Spinner and Jerkline Roller Assemblies,
            Auxiliary Brake Coupling, PARMAC 7040 Emalgo Auxiliary Brake
            (Rebuilt), Controls For Drawworks and Brake Operation (New and Rebuilt)

ITEM 1001A - Electric Motor Drive Arrangment with Two (2) G. E. 752 Series
            Wound DC Traction Motors.  Each Motor to Include a 10 HP Blower
            And Junction Box with Lockout Switch (Rebuilt)

ITEM 1002 – 1 EACH CROWN BLOCK SAVER WITH THE FOLLOWING:
            One (1) Manually Operated, 4-Way, 2- Position Air Valve for Selecting
            Normal or Override Function.
            One (1) Toggle Actuated, 2-Way, 2-Position Air Valve for Supplying
            Air Pressure to Set the Brake and Interrupt Air Supply to The Drum
            Clutches at a Pre-Determined Safe Height of Traveling Block
            Upward Travel.
            One (1) 4” x 12” Air Cylinder with Clutch Attachment to Apply to
            The Drum Brake Independent of the Manual Brake Level.
            One (1) Air Pilot Operated, 3-Way, 2-Position Air Relay Valve for
            Sensing When the Toggle Valve Has Been Actuated, thus Blocking
            The Air Supply To the Drum Clutch Selector Valve, and
            Simultaneously Venting the Drum Clutches.
            One (1) Toggle Valve Mounting Track for Mounting and Positioning
            The Toggle Valve Over the Drawworks Wire Rope Drum.
 
ITEM 1004 - One (1) Anchor, Deadline, Hercules HA-131T or Equal,
            100.000# Deadline Load with Brass for 1-3/8” Wire Rope (Rebuilt)

ITEM 1005 - One (1) National 660H500 Traveling Block, 500-Ton Capacity
            With Six – 50” Sheaves Grooved For 1-3/8” Line (Rebuilt)

            ITEM 1006 - One (1) National HA500 Hook, 500 Ton Capacity (Rebuilt)

            ITEM 1007 - One (1) Each PC 500 Ton-Capacity (Rebuilt)

            ITEM 1008 - One (1) Each NEW 5,000 PSI Hammer Union Kit Joint Swivel
                        To Rotary Hose

            ITEM 1009 - One (1) Each OILWELL 37.5”B Rotary.  OILWELL Transmission
                        With G.E. 752 ELECTRIC Motor
                                                                        _______________

SECTION 2000 – MUD PUMPS and ACCESSORIES

ITEM 2001 - Two (2) NEW FB-1600 HP Single Acting Triplex Slush Pimp,
            1600 HP Input Complete With (NEW), Fully Enclosed Fabricated Steel
            Power End, Double HELICAL Gears, Double Extended Pinion Shaft,
            Self-Aligning Spherical Main and Pinion Shaft Bearings, Roller
            Bearings at Crank and Cross Head End of Connecting Rods, Shim-
            Adjustable and Replaceable Crosshead Guide, Oilbath and Positive
            Flow Lubrication Systems, Electric Motor-Driven External Circulating
            Lube Oil Pump and Filter, with AC Motor, Oil Gauge and
            Associated Piping, Fluid Ends and Expendables, Suction and
            Discharge Manifolds, liner Flushing Pump and Reservoir, Includes
            AC Electric Motor, Piping, Manifold and Hose, Companion Flange
            For Suction Manifold.

ITEM 2002 - One (1) New Pump, Supercharging 6 x 5 With Mechanical Seal,
            Mounted On an OILFIELD Base With Coupling, OSHA Coupling Guard,
            And a 75 HP, 1200 RPM, 480 Volt, 3-Phase, 60 HZ XP AC Motor

ITEM 2003 - One (1) New Pump Unitization Complete With – Structural
            Steel, Three Runner Skid – Two V-Belt Drives, with Belts and
            Sheaves, Structural Steel Motor Sub-base with Two Adjustable
            Motor Base Plates
  
ITEM 2003A – Electric Motor Drive Arrangement with Two G.E. 752 Series
            Wound DC Traction Motors.  Each Motor to Include One (1) 10 HP
            Blower And Junction Box With Lockout Switch (Rebuilt)

ITEM 2004 - One (1) New Pulsation Dampner, 5,000 PSI Maximum Service
            Pressure, 20-Gallon Surge Capacity, 4” API 5,000 Ring Joint
            Connection.
                                   
ITEM 2005 – One (1) New Valve, Relief, Retsco-Type Manual Reset,
            1500 – 5000 PSI With Flange Connections.

ITEM 2006 - One (1) New Gauge, Pressure, 0 – 5000 PSI Range with
            Flange Connections

ITEM 2007 - One (1) New Discharge Strainer Block Assembly Complete
            With Support And 4” API 5000 LB Flanged Top and Two 5” API
            5000 LB Studded Outlets and One 5” API 5000 LB Blind Flange.

                                                __________________

SECTION 3000  - POWER AND CONTROL SYSTEM

ITEM 3001 – 3 Each CATERPILLAR 3512 Land Generator Sets as
            Follows (New): CATERPILLAR Model 3512C Land Electric
            Engine,Tier ll, 2006 EPA NON-Road Emission Certified.
            Direct Injected, Turbocharged, AfterCooler.  Separate Circuit
            Aftercooled.  Optimized for Low Emissions.  Engine Rating is
            1476 HP @ 1200 RPM.

            AIR INLET SYSTEM:  Aftercooler Core, Corrosion Resistant Air
            Cleaner, Regular Dun with Soot Filter Service Indicators

            CONTROL SYSTEM:  Caterpillar ADEM A3 ECM, Left Hand
            Requires 24 Volt DC, 10 AMP Continuous, 20 AMP Intermittent
            Clean Electrical Power.
  
            RADIATOR COOLED LAND BASED:  Outlet Controlled Thermostat
            And Housing Jacket Water Pump Gear Driven Dual Outlet,
            Aftercooled Fresh Water Cooling Pump (SCAC) Gear Driven
            Centrifugal SCAC Pump Circuit Contains a Thermostat to keep
            The Aftercooler Coolant From Falling Below 30 Degrees C (85F)

            FLYWHEELS and FLYWHEEL HOUSINGS:  Flywheel, SAE NO. 00
            Flywheel Housing, SAE No. 00 SAE Standard Rotation

            FUEL SYSTEM:   Fuel Filter, Fuel Transfer Pump, Flexible Fuel
            Lines, Fuel Priming Pump – Left Hand, Electronically Controlled
            Unit Injectors.

            INSTRUMENTATION:   Electronic Instrument Panel, Left Hand
            Analog Gauges with Digital Display Data for the Following:
            Engine Oil Pressure Gauge, Engine Water Temperature Gauge,
            Fuel Pressure Gauge, System DC Voltage gauge, Air Inlet Restriction
            Gauge, Exhaust Temperature (Prior to Turbochargers Gauge), Fuel
            Filter Differential Pressure Gauge, Oil Filter Differential pressure
            Gauge, Service Meter (Digital Display Only), Tachometer (Digital),
            Instantaneous and Total Fuel Consumption (Digital), Instantaneous
            Fuel Use (Digital), Engine Start-Stop (Off, Auto Start, Manual Start,
            Cool Down Timer)

            LUBE SYSTEM:   Crankcase Breather, Oil Cooler, Oil Filter, Shallow
            Oil Pan, Oil Pan Drain Valve – 2” NPT Female Connection, Lubricating
            Oil – SAE 10W30, Caterpillar DEO (CG4) 643L

            MOUNTING SYSTEM:   Rails, Mounting, Floor Type, 254 MM (10 IN.)

            POWER TAKE-OFFS:   Accessory Drive, Lower Left Hand Front –
            (Available For PTO), Front Housing, Two Sided.

            PROTECTION SYSTEM:   ADEM A3 ECM Monitoring System
            Provides Engine Safety Shutoff Protection, Electrical:  Oil Pressure,
            Water Temperature, Overspeed, Crankcase Pressure, Aftercooleer
            Temperature.   Includes Air Inlet Shutoff, Activated On Overspeed or
            Emergency Stop.

            ELECTRICAL ALARMS:   ECM Voltage, Oil Pressure, Water Temp
            (Low and High), Overspeed, Crankcase Pressure, Aftercooler Temp,
            Low Water Level, Air Inlet Restriction, Exhaust Stack Temp, Filter
            Differential Pressure (Oil and Fuel).
               
            DERATE, ELECTRICAL:   High Water Temp., Crancase Pressure,
            Aftercooler Temperature, Air Inlet Restriction, Altitude, Exhaust
            Temperature.

            EMERGENCY STOP PUSH BUTTON:   Located on Instrument
            Panel

            ALARM SWITCHES (OIL PRESSURE AND WATER TEMPERATURE)
            For Connections To Customer Supplied Alarm Panel.  Un-Wired.

            STARTING SYSTEM:  Air starting Motor, Right Hand, 620 to 1034
            KPA (90-150PSI), Left Hand Control Air Silencer.

            GENERAL:  Paint, Caterpillar Yellow, Vibration Damper and Guard
            Lifting Eyes.

            ADDERS:      GENERATOR, Includes 3-Point Mounting Provisions
                                    For Installation To Master Skid
                                    CATERPILLAR SR4B, 1750 KVA Generator, 2-Bearing
                                    1225 KW, 867 KW Frame, .7 PF, 600 Volt, Complete
                                    With Stator RTD’s, Space Heater, Bus Bar and Cable
                                    Access Box.
                                    CONVENTIONAL Style Split Core Radiator (56 Sq. Ft.)
                                    With 2- Circuits For Engine Jacket Water and Aftercooler.                                             Includes 78” Blower Fan, Fan Pullies, Belt Guard, Belts,
                                    Fan Guard, Fuel Cooler And Water Connections.

ITEM 3002 – 3 Each New Oil Field Skid and House Package With Unitization
            Includes The Following:

            APPROXIMATELY 10’ Wide x 40’ Long Oil Field Master Skid With
            Loading Hitches For Tailboarding .

            REMOVABLE ROOF (Curved Design)

            12” LOW PROFILE MUFFLER With Exhaust Piping

            FUEL AND AIR PIPING With Couplings For Connections To Engine
            And Between Skids.
             

            ITEM 3003 – 2 Each QUINCY 350 COMPRESSORS, Each Powered By a
            15 HP, 480 Volt, 3 Phase, 60 HZ AC Motor.  Each Compressor To Be
            Mounted on a 120 Gallon Air Receiver.  Each Compressor To Deliver
            102.1 CFM At 125 PSIG    

            ITEM 3004 – 1 Each NEW COLD START – GARDNER-DENVER HDR5-3
            Self Contained Cold Start Unit Powered By a LOMBARDINI 8 HP
            Diesel Engine.   Unit Capable of Delivering 16.5 CFM at 125 PSIG.

            ITEM 3005 – 2 Each New Air Receiver – 240 Gallon With Pressure Relief                    Valve, Gauge and Piping.

            ITEM 3006 – 1 Each New IEC Baylor 3 x 4 SCR System Designed to
            Operate

            THREE (3) CATERPILLAR 35112C Diesel Engines With 1750 KVA,
            600 Volt, 60 HZ Generators.

            DRAWWORKS:       2000 HP With (2) Motors
            MUD PUMP 1:          1600 HP With (2) Motors
            MUD PUMP 2:          1600 HP With (2) Motors

            SYSTEM WILL INCLUDE:

            THREE (3) Generator Cubicles

            FOUR (4) SCR Cubicles

            DRILLER’S Control Console

            FOOT THROTTLE
            ONE (1)  750 KVA, 600:480 Volt, 3-Phase Motor Control Center
            Transformer.

            ONE (1) 150 WA, 600:120Y208 Volt, 3-Phase, 60 HZ, Lighting
            Transformer.

            480 Volt MCC to Operate Auxiliary Equipment Included in This
            Specification.

            36- Circuit, 120Y208 Lighting Distribution Panel.

            24-Circuit, 120Y208 Volt Lighting Panel.

            SCR House is Installed in a 10 FT. wide x 40 FT. Long
            X 9 FT. High Plug Panel & Air Conditioning.

            SCR House to Have TWO (2) 7.5 Ton Air Conditioning Units
            Totaling 15 Tons.

SECTION 4000 – MAST & SUBSTRUCTURE

ITEM 4001 – 1 Each API 4F LEE C. MOORE 142’ High Cantilevered Mast,
            Static Hook Load Capacity of 1,330,000 Lbs. With 12-Lines Strung
            To The Traveling Block.  Beam Leg (Rebuilt & Certified) 30 FT.
            Leg Spread.

            CROWN BLOCK Having One (1) 60” Diameter Fabricated Steel
            Fast Line Sheave and Six (6) 50” Diameter Fabricated Steel Working
            Sheaves Mounted on Tapered Roller Bearings.   Deadline On Off
            Driller’s Side (Rebuilt)

            SHEAVES GROOVED For 1-3/8” Diameter Wireline.

            ADJUSTABLE RACKING PLATFORM Having a Capacity to
            Accommodate 242- Strands of 5” Drill Pipe and 16 Strands of 9”
            Drill Collars.  Working Platform and 4” High Hand Rails to be
            Included.

            MAST BELLY BOARD

            SET TONG COUNTER WEIGHTS Complete With Buckets, Guides,
            Blocks and Wirelines.

            SET RAISING LINES With Pull Test Certificates.

            SLINGLINES EQUALIZER UNIT.

ITEM 4002 – 1 Each API 4F LEE C. MOORE LOW LIFT Substructure, 30 FT.
            Floor Height.  Having a Casing Capacity of 900,000 LBS. and a
            Setback Capacity of 800,000 LBS.  Substructure Designed To
            Accommodate a 2000 HP Electric Drawworks and Driller’s Side
            Doghouse.  Drawworks Will Set a 5 FT. Ground Level.

            CHECKERD FLOOR PLATE ¼”

            SET HANDRIILS FOR DRILL FLOOR   V-Door, 5’ Wide With Two (2)
            4” Rail Pipes and 3/8” Flat Plate On Ramp.
             
            THREE (3) NEW Single Flight Stair System With Hand Rails.  One Stair
            System Will Run From V-Door Side of Drill Floor Straight To The
            Ground, One Stair System Will Run From Driller’s Cabin
            To Ground.
 
ITEM 4003 – 1 Each 5” Single Standpipe Assembly, 63’ Tall, With Clamps
            Installed On Off- Driller’s Side.  Weld On Type Unions Built With
            Schedule XXH Pipe To Be Utilized.
 
ITEM 4004 – 1 Each Rathole Scabbard

ITEM 4005 – 1 Each Mousehole Scabbard

ITEM 4006 – 1 Each Mast Assembly Stand To Support Mast Section Prior
            To Raising.  Scoping From 8 FT. To 33 FT.

ITEM 4007 – 1 Each 12” Flow Line.

SECTION 5000 – MUD SYSTEM AND ACCESSORIES

NEW THREE (3) TANK MUD SYSTEM HAVING A TOTAL CAPACITY OF
1500 BBL.  TANK GENERAL CONSTURUTION AS FOLLOWS:
THREE RUNNERS Oilfield Type Skid 7’-10” Wide With Oilfield Type
Skid Ends For Tail Boarding.  Skid Extensions Decked With ¼” Plate.
Tank Walls Rimmed With 6” Square Tubing Full Length of Tanks.  Tank
Sides and End Walls Constructed Of 1-1/4” Crimped Plate for Rigidity.
ITEM 5001 – 1 Each Shaker Tank
            500 BBLS.  Four (4) Compartment Shaker Tank, 10’ Wide x 8’
            Deep x 40’ Long Mounted on a 53’ Long Skid Per Above General
            Specification and Including:

            Top Walkways of Grating Around all Equipment For Servicing.
            Includes Tubing Handrails and Toe Boards.

            Removable Walkways With Handrails To Intermediate Tank.

            One (1) Stair To Ground With Handrails.

            One (1) Water Connection To Desilter Trough.
            One (1) Water Connection to Desander Trough.

            Two (2) ODRILL/MCM Linear, Shaker To be Supplied and Instaled

            One (1) ODRILL/MCM – 12-2, 2-CONE Stand Alone Vertical
            Desander To be Supplied and Instaled.

            One (1) ODRILL/MCM 12-Cone Stand Alone Desilter To Be
            Supplied and Installed.

            One (1) 3” Bottom Mud Gun With Butterfly Valve in Each
            Compartment.

            Three (3) Clean-Out Dump Gate – One (1) Each in Desander,
            Degaser, And Desilter Compartments.

            One (1) Dumpgate Clean-Out in Sand Trap Compartment.

            Two (2) 6 x 5 Centrifugal Pumps With Mechanical Seals and 60 HP,
            1800 RPM, 480 Volt, 3-Phase, 60 HZ XP AC Motor Supplied and
            Mounted On Tank Skid Extension.  ODRLL/MCM

            One (1) 12” Bottom Equalizer To Suction Tank.

            One (1) 10” Ditch Connection To Suction Tank.
            One (1) 6” Mud Gunning Line Connection To Suction Tank.

            One (1) 4” Water Line Connection To Suction Tank

            One (1) PSI 15 HP Agitator Supplied and Mounted in Last
            Compartment Of Tanl

ITEM 5002 – SUCTION TANK:
            500 BBLS.  Four (4) Compartment Suction Tank With One (1)
            10’ x 10’ x 8’ Active Compartment, 11’ x 8’ Suction Compartments
            And One (1) 10’ x 8’ x 8’ Compartment Mounted On a 53’ Skid per
            Above General Specification and Including:

            One (1) PSI 15 HP ODRILL/MCM Agitator Supplied And Mounted
            In Each Compartment.

            Four (4) 3” Bottom Mud Guns With Butterfly Valves.

            Four (4) Dump Gates for Cleanout.

            Two (2) 12” Suction Lines, One For Each Mud Pump.  Mud Pump
            To Be Capable of Sucking From Any Compartment of The
            Suction Tank.

            Two (2) 8 x 6 Centrifugal Pumps With Mechanical Seals, Each
            Powered By a 100 HP, 1800 RPM, 480 Volt, 3-Phase, 60 HZ XP
            AC Motor Supplied And Mounted On Tank Porch For Mud Mix.

            6” Suction Line in Each Compartment Of The Suction Tank
            For Tank Mix.

            6” Discharge From Mud Mix In Each Suction Tank Compartment.

            One (1) 6” Hopper to Suck Or Mix Mud in Any Suction
            Compartment.

ITEM 5003 Suction System:
            Suction System For Two (2) Pumps As Follows:

            Two (2) Charging Pumps on Mud Pump Skid Extension.

            Provide Suction Connection For Supercharging Pumps
            From Suction Lines.

            Manifold Supercharger Pump Discharge For Charging TRIPLEX
            Pump At Isolation Valve in Suction Line At Pump.
             
ITEM 5004 – One (1)New High Pressure Mud System:
            One (1) 4” 5000 LB. WP High Pressure Mud Delivery System
            For Two (2) Mud Pumps as Follows:

            Provide 4” Scheduled XXH Substructure Line Complete With
            Hammer Unions At Break Point and Heavy-Duty Clamps For
            Mounting.  Hammer Unions To Be Welded On Type.

SECTION 6000 – HOUSES / TANKS / MISCELLAEOUS EQUIPMENT

ITEM 6001 – 1 Each – NEW DRILL WATER TANK:
            10’-6” Diameter x 32’ Long Tank Mounted on an Approximately
            40’ Long Oilfield Type Skid With Loading Hitches For Tailboarding
            500 Barrel Capacity.  Two (2) MCM 3 x 2 Centrifugal Pumps
            With Rope Packing.  Each Pump To be powered by a 25 HP
            1800 RPM, 480 Volt, 3-phase, 60 HZ XP AC Motor, Pumps To Be
            Mounted On Tank Porch,

ITEM 6002 – 1 Each – PRIMARY FUEL TANK:
            8’ Diameter x 30’ Long Tank Mounted On an Approximately
            40’ Long Oilfield Type Skid With Loading Hitches For
            Tailboarding 13,000 Gallons.

            Two (2) Roper AMD-27 Gear Pumps With 3 HP, 1800 RPM, 480 Volt
            3-Phase, 60 HZ XP Motors, Local Start/Stop And Filter System
            To Be Mounted On Unit.

ITEM 6003 – 1 Each – NEW WORKSHOP / CHANGE HOUSE:
 
            8’ Wide x 38’ Long x 8’ Clear Ceiling Height Workshop Mounted
            On a 40’ Long Oilfield Type Skid Loading Hitches for Tailboarding
            House To Be Fabricated Of ¼” V-Crimp Material.  Top Of Skid
            To be Decked With ¼” Floor Plate.

            Tool Room With Shelving On Both Sides.

            Two (2) Personnel Doors.

            16 Lockers With Middle Bench.

ITEM 6004 – 1 Each – NEW DOGHOUSE:
            8’ Wide x 34’ Long x 8’ Clear Ceiling Height Mounted On a
            7’-10” Wide x  40’ Long 3-Runner Skid With Oilfield Type Ends For
            Tailboarding.  House Fabricated Of 3/16” Crimp Material and Skid
            Decked With ¼” Plate.

            HOUSE INCLUDES:

            One (1) Personnel Door, Two (2) Sliding Doors, One (1) Knowledge
            Box, One (1) Too Box / Bench Combination 4’ Long.

ITEM 6005 – 1 Each – NEW CATWALK:
            5’ Wide x 18” High x 60’ Long. (Two Piece)

ITEM 6006 – 1 Lot – New Cable Trays:
            One (1) Lot As Needed, Electrical Cable / Service Trays To
            Accommodate Air, Fuel, Water, And Electrical Cable.  Top of Trays
            Covered To Provide Walkways.

ITEM 6007 – 1 Each – 7500’ of 1-3/8” EIPS Drill line.

ITEM 6008 – 1 Each – Koomey 7 Station Accumulator Unit as Follows:
            Sized To Operate 13-5/8”-10M-CIW (U) Double, Single BOP, With
            13-5/8-5M HYDRILL (GK) Or Shaffer Spherical Style Annual BOP.
            220 Gallon Accumulator Capacitor.  Accumulator Will Funtion
            All Ram Cavities and Annular and Re-Supply Automatically To
            Full Operating Capacity Within Five (5) Minutes (Rebuilt).

ITEM 6009 – 6 Each – A Removable Roof Will Be Mounted Over The Top
            Of The Closing Unit.  1” Pipe For The Hydraulic Lines Will Run
            Down The Outside Of The Skid.

ITEM 6010 – 1 Each – BOP Equipment Blow Out Preventer System
            Consisting Of (Re-Built & CERTIFIED).
            ONE (1) Double BOP, 13-5/8” Schaffer 5000#
            ONE (1) Annular Hydrill GK BOP, 13-5/8” Spherical
            ONE (1) 13-5/8” Mud Cross, 5000# W/4 1/8 Outlets
 
ITEM 6011 – 2 Each – New Vibration Hoses:
            3-1/2” ID x Approximately 15’, 5000 LB. WP With 4” API Welded
            Connections.  For Connection of Mud Pumps To Substructure HP
            Mud Lines.

ITEM 6012 – New Rotary Hose:
            3-1/2” ID x 65’, 5000 LB. WP With 4” API Connections.  Complete
            With Safety Clamps, Chains, And Hammer Unions on Each End.

ITEM 6013 – 6 Each – New Pipe Racks:
            18” High x 28’ Long Triangular Pipe Rack Composed Of 5” Pipe
            With  3/4” Plate Legs.

ITEM 6014 – 2 Each – Ingersole Type Utility Winch, 5000#  SWL Utility
            Lifting, 5000# SWL Personnel Lifting.  Each Winch To Include
            Automatic Drum Mounted Band Brake, Manually Operated Drum
            Mounted Band Brake and Drum Guard.  Wire Rope Storage Capacity
            Is 680’ Of 5/8” Wire Rope.  

ITEM 6015 – 1 Each – Choke Manifold / Mud Gas Separator Skid
            Mounted As Follows:  10’ x 40’ Oilfield Type Skid With Loading
            Hitches For Tailboarding  and Provisions For Mounting Of Choke
            Manifold.  MUD/Gas Separator To Be 4’ x 20’.   Unit Will Separate
            Mud and Vent Gas.  Unit will Fold Over The Top Of The Choke
            Manifold.
            One (1) MCM Equipment 4”, 5000#, 2-1/16” Choke Manifold Complete
            With One (1) 5-Way Cross, Eight (8) 4-1/16 x 5000# Gate Valve,
            One (1) 2-1/16” x 5000# Gate Valve, One (1) 4-1/16” Adjustable Choke,
            One (1) Studded 4-Way Cross, 2-1/16 x 5000# Ports, One (1) 2-1/16”
            Flanged Mud Gauge, One (1) 2-1/16” x 5000# Adapter Flange,
            One (1 ) Blanking Plug, One (1) 2”, 1520 Hammer Nut and All Bolts/
            Nuts And All Bolts/Nuts For Flanges.  One (1) 5000# Hydraulic Choke
            And Control Panel To be Included.  Piping From Choke Manifold To
            Be included.

SECTION 7000 – RIG UP

ITEM 7001 – 1 Lot Mechanical Rig Up:
            Set and Assemble Mast And Substructure
            Install All Flooring and Handrails
            Install Stairs And  V-Doors
            Set and Align Rotary Table
            Set and Align Drawworks
            Set and Install Dog House
            Install Racking Board
            Set and Align Equipment Included
                        Mud System
                        Break Water / Trip Tank
                        Mud Pumps
                        Water Tank
                        Generator Sets
                        SCR House
                        Fuel Tank
                        Catwalk
                        Cable Trays
                        Closing Unit
                        Choke Manifold

            PROVIDE: Water Supply To Mud System Water Rim
            And Mixing System Suction Manifold.

            AIR SYSTEM:
            Provide Air Supply To Generator Set Engine Starters

            PROVIDE AND INSTALL FOLLOWING MISCELLANEOUS ITEMS:

                        Two (2) Air Hoist Stands
                        Tong Back-Up Post

ITEM 7002 - 1 Lot – ELECTRICAL RIG UP:

            All Electrical To Conform to API RP-500B.

            Provide and Install Two (2) Mast Light Strings With
            Fluorescent Light Fixtures and Obstruction Light.

            Provide and Install Rig Lighting Package, Consisting Of
            Fluorescent and Metal Halide Light For Rig Floor, Mud Tanks,
            Utility Skids, Substructure And Houses.

            Provide and Install Power and Control Cable for Generators,
            DC Motors, Driller’s Console, AC Motors and All Related
            Functions Indicated in This Description.

ITEM 7003 – Drilling Rig Components Will be Sand Blasted,
            Primed and Color Top Coated as Required.

We will Email Photos To SERIOUS Buyers, in the market for a 2000 HP
Excellent Rig, such as This one.  It is Mostly NEW, with a Few other part Refurbished.  It takes about 60 days to complete and ship it from Texas

Price on Request …Call:   800-304-9041 /  512-291-6434  /  903-882-9251

#879D7 – IDECO H-44C -  SINGLE DRUM DRAWWORKS – DRILLING RIG, 108’,  
268,000# MAST  – BOP, MUD SYSTEM, MUD PUMPS, ROTARY EQUIPMENT, TRAVLING EQUIP, HANDLING TOOLS, RIG HOUSE, ETC, – IN TOP SHAPE. 

DRAWWORKS:
            IDECO H-44C Single Drum Drawworks, 700 HP, LEBUS Grooved f/ 1-1/4”
            Drilling Line KOOMEY Crown-O-Matic, p/b (2) Detroit Engines, w/ (2) Allison
            CLBT-5860 Transmissions, FOSTER Makeup & Breakout Catheads.

MAST & SUBSTURE:      
            IDECO 108’H Telescoping Mast, 268,000# - Static Hook Load, (2) 3-Stage
            Hydraulic Raising Rams, Racking Boards, Ladders, Guy Lines, Fluorescent
            Lights, 3-1/2” ID Standpipe w/ OTECO 4” & 3” Gate Valves, Mud Pressure
            Gauge, INGERSOL-RAND 5 UH Air Hoist, IDECO Crown Block Assembly,
            IDECO 11’H x 7’W x14’L Substructure , 275,000# Setback Capacity, Right-
            Angle Rotary Drive, 10’W x 55”L Ramp

MUD PUMPS:
            (2) PZ-7 500 HP Triplex Mud Pumps, Independently p/b CAT D379 Engines
 
ROTATING EQUIPMENT:
            IDECO 20-1/2” Rotary Table w/54-1/4” Centers, VARCO Split Master
            Bushing.
            IDECO TL-200,  200-Ton Swivel
            4-1/4” x 40’ L Square Kelly
            FOSTER Model 77 Kelly Spinner
            VARCO 4KRUS Kelly Drive Bushing, Square Drive
            TIW Upper Kelly Cock
            (2) TIW Lower Kelly Cocks

TRAVELING EQUIPMENT:
            IDECO UTB-160-Shorty  160 Ton Block
            IDECO UTB 160-Shorty  160-Ton Hook
            Set of Elevator Links
             
HANDLIMG TOOLS:
            Set of WOOLLEY Type B Manual Rotary Tongs
            Set of VARCO 4-1/2” Drill Pipe Slips w/4” Dies
            Set of Varco Drill Collar Slips, 6” OD
            WOLLEY 4” Drill Pipe Elevators
            BAASH-ROSS 7” Elevators

BLOWOUT PREVENTER:
            CAMERON Type U 11” x 5000 PSI Double Ram Blowout Preventer
            Set of (2) 3-1/2” Rams
            Set of (2) 4-1/2” Rams
            Set of (2) Blind Rams
            Set of (2) Casing 7’ Rams
            Drilling Spool, 12”H x 11” x 3000 PSI w/(2) Outlets
            CAMERON 3-Station Closing Unit w/80-Gallon Spherical Accumulator
                        Bottle, Hydraulic Pump, Pneumatic Pump
            2-Station Remote Closing Unit
            CAMERON 3000 PSI BOP Choke Manifold w/4-Way Cross, (2)
                        2-2/16” x 3M & (2) 3” x 3M Gate Valves
            2-1/16” Adjustable Choke
            (2) 3-1/8” x 5000 PSI Gate Valves on Kill Side
            2-1/16” x 5000 PSI Flanged Check Valve

RIG HOUSE:
            ONSITE CHAMPION 34’,  5th Wheel Trailer (f/Rig Managers)

MUD SYSTEM:
            500 Barrel Mud Tank w/(4) Compartments, MISSION Centrifugal Desilter
            Pump, MISSION Centrifugal Mud Mixing, Stirrer Pump
            VORTEX Orbital Motion Shale Shaker
            VARCO 8-Cone Desilter
            400-Barrel Fresh Water Tank
 
AUXILLARY EQUIPMENT:
            Rig Tarps f/Floor & Sub & Derrick Board
            (2) Electric Heaters
            Numerous Crossover Heaters
            (2) Bit Subs, 4-1/2”IF Box Up x 4-1/2” Reg Box Down, Bored f/BAKER Float
            (2) Bit Subs, 3-1/2”IF Box Up x 3-1/2” Reg Box Down, Bored f/BAKER Float
            3683-Gallon Fuel Tank
            Utility House w/Accumulator Unit
            380 KW Generator Set w/14 Lights DETROIT Series 60 Engine
            CAT 275 KW Generator Set p/b CAT 3406 Diesel Engine
            Driller’s Instrument Box w/MARTIN-DECKER Clipper Type Weight Indicator,
                        ATLAS Pump Pressure Gauge, Tong Line Pull Gauge,
                        Rotary Torque Gauges
            Driller’s Instrument Console w/Control Valves f/M/B Tongs, Mud Pumps,
                        Transmission Shifters, Rotary Table & Drawworks Hoisting Clutch
            Bottom Change House w/(12) Lockers, Electric Heaters, Parts Room
            8’w x 18’L Top Dog House w/Knowledge Box, Tool Box, Electrical Outlets,
                         SATALLITE Automatic Driller, Electric Heater
            Rig Lights & Wiring
            WEB WILSON Type C Safety Clamps, 5-1/2” to 6”
            (4) 36” H x 28’ L Pipe Racks
            (5) Stairways
            V-Door Ramp
            (8) 20 Lb Fire Extinguishers – Type ABC

Arrangements will Be Made For SERIOUS BUYERS ONLY, To Inspect
This Rig.  Contact us to make arrangements for inspection.  This Rig is
Located in Western US., in VERY GOOD SHAPE, Ready for Drilling Now   

Documentation will Including all Rig Books, Equipment, Passports & Drawings.
    
PHOTOS SENT ON REQUEST.                    Call: 800-304-9041 or 512-291-6434

#807D7 –OILWELL 64B - TRAILER MTD. – 4,000’, FRANKS 96’- 250,000# SHL
DRAWWORKS, AIR DRILLERS CONTROLS (REMOTE MOUNTED)

Arrangements Can Be Made For SERIOUS BUYERS ONLY To Inspect This Rig Contact us to make arrangements for inspection. Rig In Texas.

PHOTOS ON REQUEST FOR SERIOUS BUYERS ONLY

#806D7 – EMSCO TYPE G-500 DRAWORKS –  TWO 475 HP (950 HP) CAT
ENGINES,   BUILT BY LEE C. MOORE COMPLETE WITH 9,000 FT
OF 5” YELLOW DRILL PIPE, 21 6-1/2” COLLARS.

THIS RIG IS READY TO DRILL NOW.  IT HAS HAD MUCH
MONEY SPENT ON IT TO HAVE IT ALL PUT IN EXCELLENT
SHAPE THROUGHOUT.     LOCATED IN TEXAS AREA
                                                                                   
 PHOTOS ON REQUEST FOR SERIOUS BUYERS ONLY

Arrangements Can Be Made For SERIOUS BUYERS ONLY To Inspect
This Rig.   Contact us to make arrangements for inspection.

#803D4 –  “SPEEDSTAR 22” TRAILER MOUNTED DRILLING RIG  

THIS RIG IS READY TO DRILL NOW
LOCATED IN THE CENTRAL, TX AREA

PHOTOS AVAILABLE ON REQUEST.

Arrangements Can Be Made For SERIOUS BUYERS ONLY To Inspect
This Rig. Contact us to make arrangements for inspection. 

#802D4 – BREWSTER N-3 DRAWWORKS W/ HI/LO DRUM W/ TWIN DISC
AIR CLUTCHES, FOSTER CAT HEADS, AIR CLUTCH ROTARY DRIVE (TOTAL
RE-BUILT INCLUDING CLUTCHES, CHAINS, SPROCKETS, BEARINGS,
AIR VALVES), POWERED BY CAT. D-3306 TA W/ TWIN DISC TORQUE
CONVERTER, ELECTRIC START, NEW AIR COMPRESSOR, AIR VOLUME TANK, FUEL DAY TANK (ALL NEW OR REBUILT)

Arrangements Can Be Made For SERIOUS BUYERS ONLY To Inspect
This Rig. Contact us to make arrangements for inspection.  This Rig is
Located in The Western USA, in Excellent Shape    

PHOTOS AVAILABLE ON REQUEST.

#800D4 – EMSCO A550E – 800 HP ELECTRIC DRILLING RIG – COMPLETE, P/B (3) CAT 379 DIESEL ENGINES – 550 HP EA., Ja-Co 136 ft MAST, (2) EMSCO F-800 TRIPLEX MUD PUMPS, 12,000 ft – READY TO WORK  

Arrangements Can Be Made For SERIOUS BUYERS ONLY.   To Inspect
This Rig Contact us to make arrangements for inspection.  This Rig is
Located in Western USA., in EXCELLENT SHAPE,  Drilling Now     

PHOTOS AVAILABLE ON REQUEST.

#794D4(2A) - GARDNER-DENVER 1100M DRILLING RIG – 1,500 HP – RATED AT
 16,000 FEET - 142’- 1,000,000# SLH CAPACITY – 25 ft LEG SPREAD – 473 JOINTS
  OF 5” S-135 -19.5# DRILL PIPE, 37 JOINTS. 

Arrangements Can Be Made For SERIOUS BUYERS  ONLY.    To Inspect
this Rig, Contact us to make arrangements for inspection.  This rig has
only drilled Two (2) Wells since 2006 when New.  Located in Texas and it
is in excellent shape.  Contact us for inspection. 800-304-9041

#793D4 – OIME SL-7 HELICOPTER OIL RIG – COMPLETELY MOVABLE BY AIR,
1000 HP – 131’ MAST - 510,000# - 14,000’ +/- DRILLING DEPTH – (2) OIME H700
HELI-TRIPLEX PUMPS, ETC. – TOTALLY MOVABLE TO DRILL SITE BY AIR  

Rig is Basically NEW with some parts Refurbished.  It Has Been Inspected By “SUPERIOR DERRICK”, Co. in Texas.

Arrangements Can Be Made For SERIOUS BUYERS
To Inspect This Rig.  Contact  us for arrangements.

Pictures Available on request

#792D4 – IDECO H-44C -  SINGLE DRUM – DRILLING RIG – 108’ – 268,000#  
 9,000 ft DRILLING DEPTH – 750 to 900 HP - MOUNTED ON WHEELS AND
AXLES as Follows:

Arrangements Can Be Made For SERIOUS BUYERS ONLY.   To Inspect
This Rig Contact us to make arrangements for inspection.  This Rig is
Located in Western US., in VERY GOOD SHAPE, Ready for Drilling Now   

4 PHOTOS AVAILABLE ON REQUEST.

#790D3 – WILSON SUPER 38 -  4,000 ft+ DRILLING RIG WIth 70 ft FREE STANDING DERRICK, RATED AT 175,000 lbs. WILSON DRAWWORKS, TRAILER MOUNTED – IN TEXAS 

Arrangements Can Be Made For SERIOUS BUYERS ONLY To Inspect this Rig Contact us to make arrangements for inspection.  PICTURES ON REQUEST.Rig In Texas.  (Note: Hauling Truck shown can be furnished as “Extra”)     

#788D6 – WILSON MOGUL 42 SINGLE DRUM – DRIVE IN DRILLING UNIT 7,500’ Drilling Depth, as Follows: .

Arrangements Can Be Made For SERIOUS BUYERS ONLY To Inspect this Rig Contact us to make arrangements for inspection.  14 PHOTOS ON REQUEST.

#786D7 – thIS DESCRIPTION IS FOR AN SK775SD - BASIC COMBINATION

DRILLING / WORKOVER RIG AND SUBSTRUCTURE PACKAGE – ALL 100% NEW.

#783D3 –  3,000 ft DRILLING RIG, GOOD SHAPE – COMPLETE - JUST CAME OFF
 A WELL - AVAILABLE NOW FOR IMMEDIATE DRILLING – LOCATED IN OKLA.

65 ft x 175,000# Derrick – TRAILER Mounted Rig
American Single Drum Drawworks with Air Clutch powered by 8V- 250HP Motor
Twin Disc Torque
Furnished w/ 2200 ft of 3-1/2” Drill Pipe (Deeper Drilling Possible)
10 Collars – 4-1/2”
Pipe Basket
One Set BJ Tongs
12” Brewster Rotary Table with Bushings
8V Drawworks Motor
Twin Disc Torque
NEW Air Rotary Table Clutch
7/8” Drill Line
Hydraulic Leveling Rams on Trailer
Collar Clamps
Slips – Two Sets
Complete Set of Subs
Geolograph
Diesel Light Plant
Portable Air Compressor
Engines are Air Starter
7-1/4” x 10” fxo Gardner Denver Mud Pump with 683 Detroit Engine
Mud Pump has all New Parts installed in Fluid End with 6” Liner
38’ Square Kelly
S-3 Brewster Swivel
Hyd Powered Brake Out
Kelco Make Up Cat Head
Two (2) Pipe Racks
Cat Walk
Dog House – 700 Gallon Fuel Tank – 80 Barrel Water Tank, all mounted on Trailer (Extra Hauling Equipment/Trucks, etc. Could Also be furnished if Needed) 

Contact us With Questions…1-800-304-9041

READY to DRILL NOW.  this Rig Just came off a well.  Some parts are new
or refurbished. IN Okla……SEVERAL PICTURES FURNISHED ON REQUEST
                                                           
Arrangements Can be Made FOR SERIOUS BUYERS to Inspect this Rig.
Contact Us to Make the arrangements. this Rig Won’t be here very long.

#782D3 – LEE C. MOORE 105 ft., 330,000 lb. DERRICK – WILSON GIANT
DRAWWORKS, REBUILT BY MID-TEX, RATED 600 HP, CIRCULATING
DRUM, HYDROMATIC, 600N BRAKES, POWERED BY 14 LITER 60 SERIES
DETROIT WIth 955 ALLISON TORQUE.

Traveling Block 150 ton Ideco Shorty Block

150 Ton TFS Swivel, Quick Change, NEW December 20, 2007

Substructure 16 x 8 x 40

Reagan Hydraulic Blowout Preventer 10” 3,000 lb

#1 Pump: D-700 EMSCO – 3408E 575 HP

#2 Pump: D-375 EMSCO Powered by 15 Liter Cummings 450 HP, NEW 2007

10 x 38 x 8 Water Tank with Scoping Dog House Above

Fuel Tank – 3200 Gal with Oil Lube Stations & Storage House

New Satellite Automatic Driller

2 Pin Geolograph Recorder

Rotary Table – 17-1/2” Continental EMSCO

Rotary Hose

6 x 48 Cat Walks

4 Pipe Tubs

2 Sets of pipe racks

10 – 6” Collars

Drilling Rig Equiped with Tongs and assorted Head and Slips For Drill Pipe and Collars

Rebuilt in June 6, 2007

450 Barrell 2-Tank Mud System

5 Agitators

4 Centrifugal Pumps

Linear Motion Shaker

Desander (Completely Re-maned June 3, 2007; Pumps/Electrical New)

2 Gen Sets – Cat 3306,  140KW

1 White Gen Set – 140KW

 7,000’ – 4-1/2” x Hole Drill Pipe

Contact us With Questions…1-800-304-9041

this Rig has Just came off a well Last drilled in July, 2008.  Ready to Drill Now. Most parts and pieces are new of refurbished.   

                                     SEVERAL PICTURES FURNISHED ON REQUEST

Arrangements Can be Made FOR SERIOUS BUYERS to Inspect Rig Central TX.
Contact Us to Make the arrangements

#776D4 – SPENCER HARRIS 7000 – 12,000 FT

SUB: Spencer Harris 400,000 lb.

DERRICK: Spencer Harris 250,000 lb Double

DRAWWORKS: Dugan DS-500 HP, Powered by Two Caterpillar 3306

PUMP: Ideco 550 Duplex – 15” Stroke, 6” Liner, Powered by D353 Cat.

ROTARY KELLY: 18” Gardner Denver Rotary Table (4-1/2” Square
            Kelly – 42’ Long), Varco Style Drive Bushing with 150 Ton
            Oil Well Swivel

GENERATOR HOUSE: Two Gas 140 KW, Powered by Cat. 3306’s

PITS: 1 – 54’ x 12’ 450 BBL Steel Tank

SOILDS CONTROL: Fluid Systems 3 Stage Shaker,
            Harrisburg 8 Cone Desander, 3 – Mud Agitators

MUD MIXING: 2 – 5’ x 65’ Magnum Centrifugals powered by 25 HP Elect             Motor

DOG HOUSE: 8’ x 40’ House Located on Top of Water Tanks

WATER TANK: 10’ x 45’ – 400 BBL

CAT WALK: 6’ x 45’ with 10’ V-Door

LIVING QUARTERS: 10’ x 42’ Tool Pusher House,
            2 – Bedrooms, Washer & Dryer
            Living Area with Full Kitchen

MISC: Satellite Automatic Driller,
            Martin-Decker Weight Indicator,
            2 Pen Geolograph
            5000 Gallon Skidded Fuel Tank,
            11” Annular BOP with Air Over
            Hydraulic Closing Unit

HANDLING TOOLS: 4-1/2” DP Slips,
            4-1/2” DP Elevators,
            Wolly C Tongs with
            Adjustable Heads for Casing (4-1/2” – 10-3/4”),
            Varco Collar Slips,
            6-1/4” Varco Collar Clamps,
            5 – 4-1/2” Full Hole Lift Subs for Collars,
            12-1/4” & 7-1/8” Rock Breaker,
            7-7/8” PDC Bit Breaker

DRILL STEMS: 10 – 6-1/4” Spiral Drill Collars
            7300 ft – 4-1/2” Full Hole Drill Pipe Included

Contact us With Questions…1-800-304-9041

This Rig was Refurbished in Oct., 2005 – DRILLING NOW in Texas 
           
Arrangements Can be Made FOR SERIOUS BUYERS, to Inspect Rig.
Contact us to Make the arrangements to Inspect this Operating Rig
Located In Texas.   If you Require Additional information let us Know.

#773D3 – MID-CONTINENT U-34B DRAWORKS / HAROLD LEE 96’ MAST -
TRAILER MOUNTED PORTABLE RIG INVENTORY – 6,500 f

Arrangements Can Be Made For SERIOUS BUYERS ONLY To Inspect
this Rig.  Contact us to make arrangements for Full inspection.

#766D4 - JEFCO - 30K – DRILLING RIG - CARRIER MOUNTED IN VERY GOOD SHAPE - READY TO WORK

Mounted On a PETERBUILT Model 357 (6 x 4)

CAT 3606 515 HP Engine

FULLER RTO Transmission

SULLAIR 1000 CFM  / 350 psi Compressor

Four Hydraulic Jacks

5833 ft-lbs Torque TopHead

Remote Controlled Jib Boom

7 Gallon Lubricator Pump

18 Gallon Water Injection Pump

16,000# Winch,

30,000 Pullback,

6 Pod Carousel

Single Pipe Loader

Auxiliary Mud Pump Hydraulics 

Pipe Spinner, Night Lights & Breakout Wrench

Contact us With Questions…1-800-304-9041

Arrangements Can Be Made For ONLY SERIOUS BUYERS To Inspect this Rig.  Contact us to make arrangements for inspection.

#754D4 – OIME SL-7 DRAWWORKS 1000 HP - 14,000 ft DRILLING DEPth

MAST:
            Lee C. Moore 131ft x 475,000# Capacity SHL, Racking
            Board, Boom Line, Tong Weights, Five (5) 42” Sheave
            Crown Cluster w/ 56” Fast Line Sheave, 1-1/8” Grooved,
            Derrick Shoes, Boom Pole, Derrick Lights (API 4F
            Inspection by SUPERIOR DERRICKS), (thREE NEW
DERRICK SECTIONS, REBUILT CROWN CLUSTER)
           
SUB BASE:
            Seventeen (17’) Foot High Split-Level Substructure, Rated
            450,000# Setback Capacity, V-Door, three Sets of Stairs,
            Handrails, L. C. Moore Substructure, Sub Skid Runners 5 ft.
            High x 60’ Long, New ¼” Flooring, Steps & Handrails.

DRAWWORKS:
            OIME SL-7 Drawworks, Rated 1000 HP, 1-1/8” Lebus
            Groover, 342 Hydromatic Brake, Drillers Console, Catwalk
            w/ Foster Catheads, three (3) Engine Compound
            (REMANUFACTURED) Powered By three (3) Cat  3406,
            C15 Diesel Engines, 540 HP, Transmissions, Clutches
            (NEW ENGINES)

BLOCK/HOOK:
            Continental Emsco Five (5) Sheave 1-1/8” Line Grooved,
            250 Ton Block w/ Web Wilson 250 Ton Hydra Hook
(REBUILT)
           
SWIVEL:
            Gray B44, 300 Ton Swivel (REBUILT)

ROTARY:
            Ideco 23” x 44” w/ Split Master Bushing (REBUILT)

TOP DOG HOUSE:
            Top House 7’-10” Wide x 9’ High 32’ Long w/ Knowledge
            Box, four Lockers, Shelves, V-Crimp ¼” Walls, Sand
            Blasted & Painted, three (3) runner Oilfield Skid (NEW)

BOTTOM HOUSE:
            Tool/Change House Combination, 7’-10” W x 9’ H x 40’ L,
            Sixteen (16) Lockers, Storage Shelves, V-Crimp ¼” Walls
            Sand Blasted & Painted.  three Runner Oilfield Skid  

PUMPS:
            Two F-1000 Triplex Pumps, Chinese Built, Pulsation
Dampner, Pop-Off Valve, Belts, Belt Guard, Master
Skidded (New), Powered by Cat D-399’s Diesel Engines
(REBUILT -0- HRS)

MUD PITS:
            Two (2) Mud Pits 10’ W x 8’ H x 40’ L, 1000 Barrels Capacity,
            Mud Troughs, Linear Shaker, Two (2) Cone Desander,
            Ten (10) Cone Desilter, Four (4) 6” x 5” Centrifugal Pumps,
            w/ Electrical Wiring, 75 HP Electric Motors, Two (2) 10 HP
            Agitators, Dump Gates, High and Low Pressure Piping,
Mud Hopper, NEW Desander, NEW Shale Shaker w/ Remanufactured Agitators & 10 Cone Desilter. 
NEW 6 x 5 CENTRIFUGAL PUMPS.
V-CRIMPED ¼” WALLS (LIKE NEW-RECONDITIONED)

GENERATOR HOUSE:
10’ W x 9’ H x 45’ L w/ Two (2) Cat 3406 Diesel Engines w/
Cat SR-4 325 KW Generators, Switch Gear, Control Panel,
Air Compressor, NEW HOUSE, ENGINES,
GEN. ENDS, SWITCH GEAR & CONTROL PANEL

DIESEL TANK:
10,000 Gallons Capacity, three (3) Runner Skid, Two
Transfer Pumps, Crimp ¼” V-Walls Tank, Sand Blasted &
Painted (NEW)

WATER TANK:
One (1) 500 BBL Capacity Water Tank, V-Crimp ¼” Walls,
Two (2) 3” x 2” Centrifugal Pumps Powered by 15 HP
Electric Motors, Sand Blasted & Painted (NEW)

BOP:
One (1) Hydrill GK 13-5/8” Annular, 3000# (REBUILT
CERTIFIED).  One (1) Schaffer 13-5/8” Double Ram,
5000#, w/ Four (4) 4” Outlets (CERTIFIED REBUILT)

CLOSING UNIT:
OCO, Five (5) Station, 110 Gallon, Two (2) Air Pumps,
One Triplex Hydraulic Charging Pump (NEW)

MISC.:
            Catwalk 18” H x 4’ W x 50’ L, Two Sect, 25’ Long (NEW)
            three Sets Triangular Pipe Racks, 18” H x28’ L (NEW)
            Bails 84”L x 2-1/4” Dia. (INSPECTED)
            Tongs (REBUILT)
            Drill Pipe Slips (NEW)
            Drill Collar Slips (NEW)
            4-1/2” Elevators (REBUILT)
            Air Hoist (NEW)
            Junk Box
            Drill Wire Line 1-1/8”, 4000” (NEW)
            Rig Lights (NEW)

            Electrical Wiring for Rig (NEW)

Contact us With Questions…1-800-304-9041

Rig is NEW with some parts Refurbished in Texas.

Arrangements Can Be Made For SERIOUS BUYERS
To Inspect this Rig.  Contact  us for arrangements.

#375S7 – REBUILT - SWAB  UNIT – WITH A 350 HP CUMMINS ENGINE -
NEW IN 2005, MOUNTED ON A 1979 FORD TRUCK –  MOST ITEMS NEW
OR REFURBISHED- RIG IS FIELD READY NOW.       

Cummins 350 HP Engine – 5 years Old

45’ Derrick in Good Shape

New Transmission

New Sand Line - 9/16” x 13,500 Ft   

New Sand Line Drum

New Clutch

5 Speed – Can Travel to 55 MPH Road  

Foot & Hand Throttle

Single Drum

Air Slips

New BPO

Oil Saver – Line & Pump

Sinker Bar

2 – 60 Gallon Fuel Tanks

All 10 Good Tires – 1/2 Tread Left

New Tool Boxed

#374S4 –    NEW / REBUILT - CARDWELL SWAB  UNIT – TRUCK MOUNTED -  
ON A 1994 MACK TRUCK – ALL REFURBISHED AND MANY NEW PARTS -  READY TO GO IN MARCH, 2009 – LIKE NEW

Cardwell – Single Drum Swab Unit

1994 Mack Truck Powered by a 350 HP CAT Engine

All New Brakes Adjustments and Brake Pads

Single 7 ft Double Wall Pole

Hydraulic Cylinder Raising Ram

Hydraulic Leveling Jacks

Air Clutch – 18 in

8,000 ft of New 9/16” Sand Line

All Swabbing Material, Oil Saver Pump & Lubricator

New Hydraulic Valves

New Air Valves

Powered by In-Line, 6 Cylinder Detroit

Rebuilt Standard Transmission

New Fuel Tank on Drawworks

New Tool Box

Contact us With Questions…1-800-304-9041

#368S6 ––  SKYTOP BREWSTED CARRIER MOUNTED SWAB  UNIT – READY TO GO - IT’S WORKING NOW   

SKYTOP BRESTER - 3 Axle Carrier

SKYTOP 9/16” x 19,000’ Sand Drum Capacity

8V-71 Detroit Diesel Engine

3 Speed Automatic Transmission

“NEW” Torque Converters 4/2005

“NEW” Raising Ram 9/2006

On 45” Mast

Two Hydraulic Jacks

Contact us With Questions…1-800-304-9041

#366S6 –1981 WILSON SUPER – TRUCK MOUNTED SWAB  UNIT – READY TO GO - IT’S WORKING NOW   

1981 Kenworth Powered by a 3406 Cat

13 Speed Roadrunner Tranmmission

4:11 Ratio Gears

Wilson Super Drawworks

8V71 Detroit

5 Speed Box

18” Witchita Air Clutch

LeBus Compensator

45’ Square Tube Derrick

Guiberson Type H Packoff and 2-7/8” Wire Line BOP

 9/16” x 13,000’ of Line

Contact us With Questions…1-800-304-9041

#364S6 –1987 CARDWELL K201 – CARRIER MOUNTED SWAB  UNIT –READY TO GO - IT’S WORKING NOW

Cardwell K201, Carrier Mounted with V6-73 Detroit Power

Standard 10 Speed Transmission

45 ft Mast with Floating Crown Sheave

Lebus Line Compensator

Hydraulic Leveling Jacks

Brake Spray Cooling System

Guiberson Type H Packoff and 2-7/8 Wireline BOP

11 R 225 Tires

9/16” x 16,000’ of Line

Contact us With Questions…1-800-304-9041

#362S4 – NEW 2009 SWAB UNIT WIth A 2002 INTERNATIONAL F8100     

C-10 305 HP CAT Engine, Fuller Transmission

Mounted with LTO 350  42” x 8” Weins Machine Sanddrum

350 HP Right Angle Box

DANA Spicer Divider Box

52’  4-Legged Derrick

4  Hydraulic Stiff Legs

1  Hydraulic Raising Ram

1 Pan Under Drum, 1 - Working Vise

Sprinkler Tank

Lubricator, Oil Saver Head

2-3/8” Swab Mandrels

2-7/8” Swab Mandrels

Swab Jars

ALL New Equipment – Hoses, Hydraulics, Tool Boxes, Etc.

ALL New Walkways

16,000’ of 9/16” Sandline

Painted Your Specified COLOR

Contact us With Questions…1-800-304-9041

#358S4– BRAND NEW 2009 – SWAB UNIT – ALL NEW - WIth
                 CHOICE OF NEW OR USED PETERBILT TRUCK

New Derrick with New Sheaves
New Raising Cylinders
New DINO Divider Box
New COOPER Right Angle Gear Box – 500 HP
New Lebus Compensator
New Hydraulic Jacks
New Walkways
Tooled Out and Ready to Go
16,000 ft of 9/16 Matex Sandline
Lubricators, Mandrels, Rope Sockets and Sinker Bars
Total Refurbished Wilson Draworks w/ New Brake System
With New PETERBILT Truck

Contact us With Questions…1-800-304-9041

#350S4 BRAND NEW 20098 – INTERNATIONAL 7500 SWAB  UNIT

All Mounted on International Mod. 7500 SFA 6 x 4 Truck

340 HP Engine

FULLER RTO F11908LL 10 Speed Transmission

Front Axle – 18,000#

Rear Axle – 46,000#

Mounted with LTO 350 - 42” x 8” WEINS Machine Sanddrum

350 HP Right Angle Box

DANA SPICER Divider Box

4 – Legged Derrick

4 – Hydraulic Stiff Legs

1 – Hydraulic Raising Ram

1 – Pan Under Drum

1 – Working Vise

Sprinkler Tank

All New Equipment – Hoses, Hydraulics, Tool Boxes, Etc.

All New Walkways

Painted to Your Specified Color

Contact us With Questions…1-800-304-9041

#316S3 –BRAND NEW 2009 – SWAB  UNIT

All Mounted on a 2007/2008 International 7400 SBA 6 x 4 Truck

International DT-466 Hi Torque 50 State 300 HP Diesel Engine

Allison 3000 PDS 5-Speed Auto. Trans. Electronic Controls

GX Single Drum 10” x 42” Brakes

Line Capacity – 16,000 ft of 9/16” Line Capacity

Brake Water Spray Tank

30” Hopper Clutch

Sub Frame to set On Truck w/ 4 Hydraulic Jacks w/ Safety Locks

Jack Stands

Derrick Height – 48 ft.

24” Crown Sheave

Chemical Tank w/ Spray Bar

Hydraulic Lift On Operator’s Panel

Custom Tool Boxes Mounted To Customers Preference

Kill & Start Controls On Operator’s Panel

Hydraulic Tank

Boarding Ladder

Lebus Spooling Compensator

Hooper 1 to 1 Right Angle Drive

Paint & Primer To Customer’s Specs.

Spicer 784 Drop Box Install
Junk Basket

Slobber Tank

15,000 Ft of 9/16" Installed

Call us for Current Ready-Completion of Swab Unit

Contact us With Questions…1-800-304-9041

 
WE HAVE ALSO LISTED PRICE AND A BRIEF DESCRIPTION ON OTHER RIGS BELOW.  FOR FULL INFORMATION, AVAILABILTY & PICTURES CALL US AT: 1-800-304-9041
Email:  TexacaliOil@aol.com      Website: www.oilfieldrigs.com

• All items are subject to prior sale and sold "as is, where is" without warranty, & require a signed Bill of Sale. Feel free to ask any number of questions and thoroughly examine condition of any equipment.
  

CURRENT OIL & GAS INVENTORY

SELL | LEASE/PURCHASE | FINANCE

Joseph Louden, President

Phone: (800) 304-9041 | (512) 291-6434 | Fax: (512) 291-6047
E-mail: TexacaliOil@aol.com