SECTION 1000 - DRAWWORKS AND ACCESSORIES
ITEM 1001 - 1 Each OILWELL E-2000, 2000 HP Drawworks as Follows (Rebuilt): Welded Structural Steel Frame and Housing, Drum with Grooving For
For 1-3/8” Drill Line, Water Cooled Brake Flanges, Hydraulic Spinner
And Breakout with Controls Mounted on Floor (New), 42” x 10” High
Drum Clutch (New), 36-C Two Plate Low Drum Clutch (new), Motor
Drive Chain (new), Drum Drive Chains (New), Catshaft Drive Chain (New),
Induction Hardened Cut Tooth Sprockets, Pressure Spray Oil
Lubrication to All Chains, Lubrication Pump, Self- Aligning Main Shaft
Roller Bearings, Air Controlled Transmission Clutches, Air Controlled
Catshaft Disconnect Clutch, Spinner and Jerkline Roller Assemblies,
Auxiliary Brake Coupling, PARMAC 7040 Emalgo Auxiliary Brake
(Rebuilt), Controls For Drawworks and Brake Operation (New and Rebuilt)
ITEM 1001A - Electric Motor Drive Arrangment with Two (2) G. E. 752 Series
Wound DC Traction Motors. Each Motor to Include a 10 HP Blower
And Junction Box with Lockout Switch (Rebuilt)
ITEM 1002 – 1 EACH CROWN BLOCK SAVER WITH THE FOLLOWING:
One (1) Manually Operated, 4-Way, 2- Position Air Valve for Selecting
Normal or Override Function.
One (1) Toggle Actuated, 2-Way, 2-Position Air Valve for Supplying
Air Pressure to Set the Brake and Interrupt Air Supply to The Drum
Clutches at a Pre-Determined Safe Height of Traveling Block
Upward Travel.
One (1) 4” x 12” Air Cylinder with Clutch Attachment to Apply to
The Drum Brake Independent of the Manual Brake Level.
One (1) Air Pilot Operated, 3-Way, 2-Position Air Relay Valve for
Sensing When the Toggle Valve Has Been Actuated, thus Blocking
The Air Supply To the Drum Clutch Selector Valve, and
Simultaneously Venting the Drum Clutches.
One (1) Toggle Valve Mounting Track for Mounting and Positioning
The Toggle Valve Over the Drawworks Wire Rope Drum.
ITEM 1004 - One (1) Anchor, Deadline, Hercules HA-131T or Equal,
100.000# Deadline Load with Brass for 1-3/8” Wire Rope (Rebuilt)
ITEM 1005 - One (1) National 660H500 Traveling Block, 500-Ton Capacity
With Six – 50” Sheaves Grooved For 1-3/8” Line (Rebuilt)
ITEM 1006 - One (1) National HA500 Hook, 500 Ton Capacity (Rebuilt)
ITEM 1007 - One (1) Each PC 500 Ton-Capacity (Rebuilt)
ITEM 1008 - One (1) Each NEW 5,000 PSI Hammer Union Kit Joint Swivel
To Rotary Hose
ITEM 1009 - One (1) Each OILWELL 37.5”B Rotary. OILWELL Transmission
With G.E. 752 ELECTRIC Motor
_______________
SECTION 2000 – MUD PUMPS and ACCESSORIES
ITEM 2001 - Two (2) NEW FB-1600 HP Single Acting Triplex Slush Pimp,
1600 HP Input Complete With (NEW), Fully Enclosed Fabricated Steel
Power End, Double HELICAL Gears, Double Extended Pinion Shaft,
Self-Aligning Spherical Main and Pinion Shaft Bearings, Roller
Bearings at Crank and Cross Head End of Connecting Rods, Shim-
Adjustable and Replaceable Crosshead Guide, Oilbath and Positive
Flow Lubrication Systems, Electric Motor-Driven External Circulating
Lube Oil Pump and Filter, with AC Motor, Oil Gauge and
Associated Piping, Fluid Ends and Expendables, Suction and
Discharge Manifolds, liner Flushing Pump and Reservoir, Includes
AC Electric Motor, Piping, Manifold and Hose, Companion Flange
For Suction Manifold.
ITEM 2002 - One (1) New Pump, Supercharging 6 x 5 With Mechanical Seal,
Mounted On an OILFIELD Base With Coupling, OSHA Coupling Guard,
And a 75 HP, 1200 RPM, 480 Volt, 3-Phase, 60 HZ XP AC Motor
ITEM 2003 - One (1) New Pump Unitization Complete With – Structural
Steel, Three Runner Skid – Two V-Belt Drives, with Belts and
Sheaves, Structural Steel Motor Sub-base with Two Adjustable
Motor Base Plates
ITEM 2003A – Electric Motor Drive Arrangement with Two G.E. 752 Series
Wound DC Traction Motors. Each Motor to Include One (1) 10 HP
Blower And Junction Box With Lockout Switch (Rebuilt)
ITEM 2004 - One (1) New Pulsation Dampner, 5,000 PSI Maximum Service
Pressure, 20-Gallon Surge Capacity, 4” API 5,000 Ring Joint
Connection.
ITEM 2005 – One (1) New Valve, Relief, Retsco-Type Manual Reset,
1500 – 5000 PSI With Flange Connections.
ITEM 2006 - One (1) New Gauge, Pressure, 0 – 5000 PSI Range with
Flange Connections
ITEM 2007 - One (1) New Discharge Strainer Block Assembly Complete
With Support And 4” API 5000 LB Flanged Top and Two 5” API
5000 LB Studded Outlets and One 5” API 5000 LB Blind Flange.
__________________
SECTION 3000 - POWER AND CONTROL SYSTEM
ITEM 3001 – 3 Each CATERPILLAR 3512 Land Generator Sets as
Follows (New): CATERPILLAR Model 3512C Land Electric
Engine,Tier ll, 2006 EPA NON-Road Emission Certified.
Direct Injected, Turbocharged, AfterCooler. Separate Circuit
Aftercooled. Optimized for Low Emissions. Engine Rating is
1476 HP @ 1200 RPM.
AIR INLET SYSTEM: Aftercooler Core, Corrosion Resistant Air
Cleaner, Regular Dun with Soot Filter Service Indicators
CONTROL SYSTEM: Caterpillar ADEM A3 ECM, Left Hand
Requires 24 Volt DC, 10 AMP Continuous, 20 AMP Intermittent
Clean Electrical Power.
RADIATOR COOLED LAND BASED: Outlet Controlled Thermostat
And Housing Jacket Water Pump Gear Driven Dual Outlet,
Aftercooled Fresh Water Cooling Pump (SCAC) Gear Driven
Centrifugal SCAC Pump Circuit Contains a Thermostat to keep
The Aftercooler Coolant From Falling Below 30 Degrees C (85F)
FLYWHEELS and FLYWHEEL HOUSINGS: Flywheel, SAE NO. 00
Flywheel Housing, SAE No. 00 SAE Standard Rotation
FUEL SYSTEM: Fuel Filter, Fuel Transfer Pump, Flexible Fuel
Lines, Fuel Priming Pump – Left Hand, Electronically Controlled
Unit Injectors.
INSTRUMENTATION: Electronic Instrument Panel, Left Hand
Analog Gauges with Digital Display Data for the Following:
Engine Oil Pressure Gauge, Engine Water Temperature Gauge,
Fuel Pressure Gauge, System DC Voltage gauge, Air Inlet Restriction
Gauge, Exhaust Temperature (Prior to Turbochargers Gauge), Fuel
Filter Differential Pressure Gauge, Oil Filter Differential pressure
Gauge, Service Meter (Digital Display Only), Tachometer (Digital),
Instantaneous and Total Fuel Consumption (Digital), Instantaneous
Fuel Use (Digital), Engine Start-Stop (Off, Auto Start, Manual Start,
Cool Down Timer)
LUBE SYSTEM: Crankcase Breather, Oil Cooler, Oil Filter, Shallow
Oil Pan, Oil Pan Drain Valve – 2” NPT Female Connection, Lubricating
Oil – SAE 10W30, Caterpillar DEO (CG4) 643L
MOUNTING SYSTEM: Rails, Mounting, Floor Type, 254 MM (10 IN.)
POWER TAKE-OFFS: Accessory Drive, Lower Left Hand Front –
(Available For PTO), Front Housing, Two Sided.
PROTECTION SYSTEM: ADEM A3 ECM Monitoring System
Provides Engine Safety Shutoff Protection, Electrical: Oil Pressure,
Water Temperature, Overspeed, Crankcase Pressure, Aftercooleer
Temperature. Includes Air Inlet Shutoff, Activated On Overspeed or
Emergency Stop.
ELECTRICAL ALARMS: ECM Voltage, Oil Pressure, Water Temp
(Low and High), Overspeed, Crankcase Pressure, Aftercooler Temp,
Low Water Level, Air Inlet Restriction, Exhaust Stack Temp, Filter
Differential Pressure (Oil and Fuel).
DERATE, ELECTRICAL: High Water Temp., Crancase Pressure,
Aftercooler Temperature, Air Inlet Restriction, Altitude, Exhaust
Temperature.
EMERGENCY STOP PUSH BUTTON: Located on Instrument
Panel
ALARM SWITCHES (OIL PRESSURE AND WATER TEMPERATURE)
For Connections To Customer Supplied Alarm Panel. Un-Wired.
STARTING SYSTEM: Air starting Motor, Right Hand, 620 to 1034
KPA (90-150PSI), Left Hand Control Air Silencer.
GENERAL: Paint, Caterpillar Yellow, Vibration Damper and Guard
Lifting Eyes.
ADDERS: GENERATOR, Includes 3-Point Mounting Provisions
For Installation To Master Skid
CATERPILLAR SR4B, 1750 KVA Generator, 2-Bearing
1225 KW, 867 KW Frame, .7 PF, 600 Volt, Complete
With Stator RTD’s, Space Heater, Bus Bar and Cable
Access Box.
CONVENTIONAL Style Split Core Radiator (56 Sq. Ft.)
With 2- Circuits For Engine Jacket Water and Aftercooler. Includes 78” Blower Fan, Fan Pullies, Belt Guard, Belts,
Fan Guard, Fuel Cooler And Water Connections.
ITEM 3002 – 3 Each New Oil Field Skid and House Package With Unitization
Includes The Following:
APPROXIMATELY 10’ Wide x 40’ Long Oil Field Master Skid With
Loading Hitches For Tailboarding .
REMOVABLE ROOF (Curved Design)
12” LOW PROFILE MUFFLER With Exhaust Piping
FUEL AND AIR PIPING With Couplings For Connections To Engine
And Between Skids.
ITEM 3003 – 2 Each QUINCY 350 COMPRESSORS, Each Powered By a
15 HP, 480 Volt, 3 Phase, 60 HZ AC Motor. Each Compressor To Be
Mounted on a 120 Gallon Air Receiver. Each Compressor To Deliver
102.1 CFM At 125 PSIG
ITEM 3004 – 1 Each NEW COLD START – GARDNER-DENVER HDR5-3
Self Contained Cold Start Unit Powered By a LOMBARDINI 8 HP
Diesel Engine. Unit Capable of Delivering 16.5 CFM at 125 PSIG.
ITEM 3005 – 2 Each New Air Receiver – 240 Gallon With Pressure Relief Valve, Gauge and Piping.
ITEM 3006 – 1 Each New IEC Baylor 3 x 4 SCR System Designed to
Operate
THREE (3) CATERPILLAR 35112C Diesel Engines With 1750 KVA,
600 Volt, 60 HZ Generators.
DRAWWORKS: 2000 HP With (2) Motors
MUD PUMP 1: 1600 HP With (2) Motors
MUD PUMP 2: 1600 HP With (2) Motors
SYSTEM WILL INCLUDE:
THREE (3) Generator Cubicles
FOUR (4) SCR Cubicles
DRILLER’S Control Console
FOOT THROTTLE
ONE (1) 750 KVA, 600:480 Volt, 3-Phase Motor Control Center
Transformer.
ONE (1) 150 WA, 600:120Y208 Volt, 3-Phase, 60 HZ, Lighting
Transformer.
480 Volt MCC to Operate Auxiliary Equipment Included in This
Specification.
36- Circuit, 120Y208 Lighting Distribution Panel.
24-Circuit, 120Y208 Volt Lighting Panel.
SCR House is Installed in a 10 FT. wide x 40 FT. Long
X 9 FT. High Plug Panel & Air Conditioning.
SCR House to Have TWO (2) 7.5 Ton Air Conditioning Units
Totaling 15 Tons.
SECTION 4000 – MAST & SUBSTRUCTURE
ITEM 4001 – 1 Each API 4F LEE C. MOORE 142’ High Cantilevered Mast,
Static Hook Load Capacity of 1,330,000 Lbs. With 12-Lines Strung
To The Traveling Block. Beam Leg (Rebuilt & Certified) 30 FT.
Leg Spread.
CROWN BLOCK Having One (1) 60” Diameter Fabricated Steel
Fast Line Sheave and Six (6) 50” Diameter Fabricated Steel Working
Sheaves Mounted on Tapered Roller Bearings. Deadline On Off
Driller’s Side (Rebuilt)
SHEAVES GROOVED For 1-3/8” Diameter Wireline.
ADJUSTABLE RACKING PLATFORM Having a Capacity to
Accommodate 242- Strands of 5” Drill Pipe and 16 Strands of 9”
Drill Collars. Working Platform and 4” High Hand Rails to be
Included.
MAST BELLY BOARD
SET TONG COUNTER WEIGHTS Complete With Buckets, Guides,
Blocks and Wirelines.
SET RAISING LINES With Pull Test Certificates.
SLINGLINES EQUALIZER UNIT.
ITEM 4002 – 1 Each API 4F LEE C. MOORE LOW LIFT Substructure, 30 FT.
Floor Height. Having a Casing Capacity of 900,000 LBS. and a
Setback Capacity of 800,000 LBS. Substructure Designed To
Accommodate a 2000 HP Electric Drawworks and Driller’s Side
Doghouse. Drawworks Will Set a 5 FT. Ground Level.
CHECKERD FLOOR PLATE ¼”
SET HANDRIILS FOR DRILL FLOOR V-Door, 5’ Wide With Two (2)
4” Rail Pipes and 3/8” Flat Plate On Ramp.
THREE (3) NEW Single Flight Stair System With Hand Rails. One Stair
System Will Run From V-Door Side of Drill Floor Straight To The
Ground, One Stair System Will Run From Driller’s Cabin
To Ground.
ITEM 4003 – 1 Each 5” Single Standpipe Assembly, 63’ Tall, With Clamps
Installed On Off- Driller’s Side. Weld On Type Unions Built With
Schedule XXH Pipe To Be Utilized.
ITEM 4004 – 1 Each Rathole Scabbard
ITEM 4005 – 1 Each Mousehole Scabbard
ITEM 4006 – 1 Each Mast Assembly Stand To Support Mast Section Prior
To Raising. Scoping From 8 FT. To 33 FT.
ITEM 4007 – 1 Each 12” Flow Line.
SECTION 5000 – MUD SYSTEM AND ACCESSORIES
NEW THREE (3) TANK MUD SYSTEM HAVING A TOTAL CAPACITY OF
1500 BBL. TANK GENERAL CONSTURUTION AS FOLLOWS:
THREE RUNNERS Oilfield Type Skid 7’-10” Wide With Oilfield Type
Skid Ends For Tail Boarding. Skid Extensions Decked With ¼” Plate.
Tank Walls Rimmed With 6” Square Tubing Full Length of Tanks. Tank
Sides and End Walls Constructed Of 1-1/4” Crimped Plate for Rigidity.
ITEM 5001 – 1 Each Shaker Tank
500 BBLS. Four (4) Compartment Shaker Tank, 10’ Wide x 8’
Deep x 40’ Long Mounted on a 53’ Long Skid Per Above General
Specification and Including:
Top Walkways of Grating Around all Equipment For Servicing.
Includes Tubing Handrails and Toe Boards.
Removable Walkways With Handrails To Intermediate Tank.
One (1) Stair To Ground With Handrails.
One (1) Water Connection To Desilter Trough.
One (1) Water Connection to Desander Trough.
Two (2) ODRILL/MCM Linear, Shaker To be Supplied and Instaled
One (1) ODRILL/MCM – 12-2, 2-CONE Stand Alone Vertical
Desander To be Supplied and Instaled.
One (1) ODRILL/MCM 12-Cone Stand Alone Desilter To Be
Supplied and Installed.
One (1) 3” Bottom Mud Gun With Butterfly Valve in Each
Compartment.
Three (3) Clean-Out Dump Gate – One (1) Each in Desander,
Degaser, And Desilter Compartments.
One (1) Dumpgate Clean-Out in Sand Trap Compartment.
Two (2) 6 x 5 Centrifugal Pumps With Mechanical Seals and 60 HP,
1800 RPM, 480 Volt, 3-Phase, 60 HZ XP AC Motor Supplied and
Mounted On Tank Skid Extension. ODRLL/MCM
One (1) 12” Bottom Equalizer To Suction Tank.
One (1) 10” Ditch Connection To Suction Tank.
One (1) 6” Mud Gunning Line Connection To Suction Tank.
One (1) 4” Water Line Connection To Suction Tank
One (1) PSI 15 HP Agitator Supplied and Mounted in Last
Compartment Of Tanl
ITEM 5002 – SUCTION TANK:
500 BBLS. Four (4) Compartment Suction Tank With One (1)
10’ x 10’ x 8’ Active Compartment, 11’ x 8’ Suction Compartments
And One (1) 10’ x 8’ x 8’ Compartment Mounted On a 53’ Skid per
Above General Specification and Including:
One (1) PSI 15 HP ODRILL/MCM Agitator Supplied And Mounted
In Each Compartment.
Four (4) 3” Bottom Mud Guns With Butterfly Valves.
Four (4) Dump Gates for Cleanout.
Two (2) 12” Suction Lines, One For Each Mud Pump. Mud Pump
To Be Capable of Sucking From Any Compartment of The
Suction Tank.
Two (2) 8 x 6 Centrifugal Pumps With Mechanical Seals, Each
Powered By a 100 HP, 1800 RPM, 480 Volt, 3-Phase, 60 HZ XP
AC Motor Supplied And Mounted On Tank Porch For Mud Mix.
6” Suction Line in Each Compartment Of The Suction Tank
For Tank Mix.
6” Discharge From Mud Mix In Each Suction Tank Compartment.
One (1) 6” Hopper to Suck Or Mix Mud in Any Suction
Compartment.
ITEM 5003 Suction System:
Suction System For Two (2) Pumps As Follows:
Two (2) Charging Pumps on Mud Pump Skid Extension.
Provide Suction Connection For Supercharging Pumps
From Suction Lines.
Manifold Supercharger Pump Discharge For Charging TRIPLEX
Pump At Isolation Valve in Suction Line At Pump.
ITEM 5004 – One (1)New High Pressure Mud System:
One (1) 4” 5000 LB. WP High Pressure Mud Delivery System
For Two (2) Mud Pumps as Follows:
Provide 4” Scheduled XXH Substructure Line Complete With
Hammer Unions At Break Point and Heavy-Duty Clamps For
Mounting. Hammer Unions To Be Welded On Type.
SECTION 6000 – HOUSES / TANKS / MISCELLAEOUS EQUIPMENT
ITEM 6001 – 1 Each – NEW DRILL WATER TANK:
10’-6” Diameter x 32’ Long Tank Mounted on an Approximately
40’ Long Oilfield Type Skid With Loading Hitches For Tailboarding
500 Barrel Capacity. Two (2) MCM 3 x 2 Centrifugal Pumps
With Rope Packing. Each Pump To be powered by a 25 HP
1800 RPM, 480 Volt, 3-phase, 60 HZ XP AC Motor, Pumps To Be
Mounted On Tank Porch,
ITEM 6002 – 1 Each – PRIMARY FUEL TANK:
8’ Diameter x 30’ Long Tank Mounted On an Approximately
40’ Long Oilfield Type Skid With Loading Hitches For
Tailboarding 13,000 Gallons.
Two (2) Roper AMD-27 Gear Pumps With 3 HP, 1800 RPM, 480 Volt
3-Phase, 60 HZ XP Motors, Local Start/Stop And Filter System
To Be Mounted On Unit.
ITEM 6003 – 1 Each – NEW WORKSHOP / CHANGE HOUSE:
8’ Wide x 38’ Long x 8’ Clear Ceiling Height Workshop Mounted
On a 40’ Long Oilfield Type Skid Loading Hitches for Tailboarding
House To Be Fabricated Of ¼” V-Crimp Material. Top Of Skid
To be Decked With ¼” Floor Plate.
Tool Room With Shelving On Both Sides.
Two (2) Personnel Doors.
16 Lockers With Middle Bench.
ITEM 6004 – 1 Each – NEW DOGHOUSE:
8’ Wide x 34’ Long x 8’ Clear Ceiling Height Mounted On a
7’-10” Wide x 40’ Long 3-Runner Skid With Oilfield Type Ends For
Tailboarding. House Fabricated Of 3/16” Crimp Material and Skid
Decked With ¼” Plate.
HOUSE INCLUDES:
One (1) Personnel Door, Two (2) Sliding Doors, One (1) Knowledge
Box, One (1) Too Box / Bench Combination 4’ Long.
ITEM 6005 – 1 Each – NEW CATWALK:
5’ Wide x 18” High x 60’ Long. (Two Piece)
ITEM 6006 – 1 Lot – New Cable Trays:
One (1) Lot As Needed, Electrical Cable / Service Trays To
Accommodate Air, Fuel, Water, And Electrical Cable. Top of Trays
Covered To Provide Walkways.
ITEM 6007 – 1 Each – 7500’ of 1-3/8” EIPS Drill line.
ITEM 6008 – 1 Each – Koomey 7 Station Accumulator Unit as Follows:
Sized To Operate 13-5/8”-10M-CIW (U) Double, Single BOP, With
13-5/8-5M HYDRILL (GK) Or Shaffer Spherical Style Annual BOP.
220 Gallon Accumulator Capacitor. Accumulator Will Funtion
All Ram Cavities and Annular and Re-Supply Automatically To
Full Operating Capacity Within Five (5) Minutes (Rebuilt).
ITEM 6009 – 6 Each – A Removable Roof Will Be Mounted Over The Top
Of The Closing Unit. 1” Pipe For The Hydraulic Lines Will Run
Down The Outside Of The Skid.
ITEM 6010 – 1 Each – BOP Equipment Blow Out Preventer System
Consisting Of (Re-Built & CERTIFIED).
ONE (1) Double BOP, 13-5/8” Schaffer 5000#
ONE (1) Annular Hydrill GK BOP, 13-5/8” Spherical
ONE (1) 13-5/8” Mud Cross, 5000# W/4 1/8 Outlets
ITEM 6011 – 2 Each – New Vibration Hoses:
3-1/2” ID x Approximately 15’, 5000 LB. WP With 4” API Welded
Connections. For Connection of Mud Pumps To Substructure HP
Mud Lines.
ITEM 6012 – New Rotary Hose:
3-1/2” ID x 65’, 5000 LB. WP With 4” API Connections. Complete
With Safety Clamps, Chains, And Hammer Unions on Each End.
ITEM 6013 – 6 Each – New Pipe Racks:
18” High x 28’ Long Triangular Pipe Rack Composed Of 5” Pipe
With 3/4” Plate Legs.
ITEM 6014 – 2 Each – Ingersole Type Utility Winch, 5000# SWL Utility
Lifting, 5000# SWL Personnel Lifting. Each Winch To Include
Automatic Drum Mounted Band Brake, Manually Operated Drum
Mounted Band Brake and Drum Guard. Wire Rope Storage Capacity
Is 680’ Of 5/8” Wire Rope.
ITEM 6015 – 1 Each – Choke Manifold / Mud Gas Separator Skid
Mounted As Follows: 10’ x 40’ Oilfield Type Skid With Loading
Hitches For Tailboarding and Provisions For Mounting Of Choke
Manifold. MUD/Gas Separator To Be 4’ x 20’. Unit Will Separate
Mud and Vent Gas. Unit will Fold Over The Top Of The Choke
Manifold.
One (1) MCM Equipment 4”, 5000#, 2-1/16” Choke Manifold Complete
With One (1) 5-Way Cross, Eight (8) 4-1/16 x 5000# Gate Valve,
One (1) 2-1/16” x 5000# Gate Valve, One (1) 4-1/16” Adjustable Choke,
One (1) Studded 4-Way Cross, 2-1/16 x 5000# Ports, One (1) 2-1/16”
Flanged Mud Gauge, One (1) 2-1/16” x 5000# Adapter Flange,
One (1 ) Blanking Plug, One (1) 2”, 1520 Hammer Nut and All Bolts/
Nuts And All Bolts/Nuts For Flanges. One (1) 5000# Hydraulic Choke
And Control Panel To be Included. Piping From Choke Manifold To
Be included.
SECTION 7000 – RIG UP
ITEM 7001 – 1 Lot Mechanical Rig Up:
Set and Assemble Mast And Substructure
Install All Flooring and Handrails
Install Stairs And V-Doors
Set and Align Rotary Table
Set and Align Drawworks
Set and Install Dog House
Install Racking Board
Set and Align Equipment Included
Mud System
Break Water / Trip Tank
Mud Pumps
Water Tank
Generator Sets
SCR House
Fuel Tank
Catwalk
Cable Trays
Closing Unit
Choke Manifold
PROVIDE: Water Supply To Mud System Water Rim
And Mixing System Suction Manifold.
AIR SYSTEM:
Provide Air Supply To Generator Set Engine Starters
PROVIDE AND INSTALL FOLLOWING MISCELLANEOUS ITEMS:
Two (2) Air Hoist Stands
Tong Back-Up Post
ITEM 7002 - 1 Lot – ELECTRICAL RIG UP:
All Electrical To Conform to API RP-500B.
Provide and Install Two (2) Mast Light Strings With
Fluorescent Light Fixtures and Obstruction Light.
Provide and Install Rig Lighting Package, Consisting Of
Fluorescent and Metal Halide Light For Rig Floor, Mud Tanks,
Utility Skids, Substructure And Houses.
Provide and Install Power and Control Cable for Generators,
DC Motors, Driller’s Console, AC Motors and All Related
Functions Indicated in This Description.
ITEM 7003 – Drilling Rig Components Will be Sand Blasted,
Primed and Color Top Coated as Required. |